cut

  1. Maple_-_First_cut

    Maple_-_First_cut

  2. pviser

    Rough Cut! Hooray!!

    Tommy Mac and his show, Rough Cut, were back on UNC-TV at 3 PM today. Which one of my NCWW colleagues do I thank for this? Back when UNC stopped airing his shows, my repeated complaining through e-mails and letters was apparently ignored. I gave up my efforts months ago. Anyway, thanks to...
  3. J

    1" rabbet cut

    I'm making the Bright Idea Candle Holder featured in Wood Magazine (July '09; issue 191) and have run into a snag. The parts on this project are small. One part in particular is 3/8" thick, 4.5" in length and 1.5" wide. The directions advise to cut a 1/8" rabbet - 1" deep into the end of this...
  4. BKind2Anmls

    Can I Cut This With a Bandsaw? Final Pix

    I epoxied some 10-gauge wire from electrical cable into a block of maple and cut it into the shape of a Christmas tree. I next want to slice it up for ornaments. Can I do this on my bandsaw with a wood cutting blade? Everything I can find on the Internet says "you can cut thin sheets of...
  5. Gary_C

    Flush cut jig for router

    I'm wondering if any of you guys have made a jig for steadying a router when using a flush cut bit. I'm a complete newbie at woodworking and saw an episode of Woodsmith that showed this jig and think it would work for my current problem. My first read wood project is a set of nesting end...
  6. allisnut

    Cut some pen blanks today...

    Spalted Oak from the firewood pile. Free pen blanks that look better than high dollar exotics! Adam
  7. AmishWarlord

    1.5 Millon tablesaw cut.

    Say goodbye to table saws that cost less than $3,000 http://www.woodmagazine.com/woodworking-tips/editorial-extras/tablesaws-lawsuit/?sssdmh=dm17.441549&esrc=nwwood&email=1376225440
  8. L

    Safe cut for split rail

    How can I safely cut a split in a 1/2" or less dowel which will be left attached on one end? I have a tablesaw and a bandsaw.
  9. Gone2dMtns

    Current value for rough cut WO

    Howdy guys! It's been while since I've logged on. I was wondering what the going rate per BF is for 8/4 rough sawn white oak. I tried to Google up the info and the prices are all over the place. Since WO is a fairly common wood here in central NC, I thought one of you might have an idea of the...
  10. CrealBilly

    From rough cut to spice rack in under an hour

    I made and finished this spice rack today. Took less than 1 hour from rough cut lumber to hanging on the wall. You may not be able to tell but the shelves have a 1/4 x 3/8" lip in the front, so the bottles don't fall out. If you can't tell that means I did a good glue job. I evoked some of...
  11. J

    Ridgid 12", 100 tooth Fine cut blade $59

    Made my trip to HF this morning and got the two HVLP sprayers I wanted for $9.99 each. After lunch, stopped at HD and they had reduced the price of their 12", 100 tooth fine cut off blade to $59, from $74. Didn't think to check and see if was an Italian made blade though.
  12. Steve_Honeycutt

    Table Saw Cross Cut Sled

    I am thinking of building a cross cut sled for my table saw. I plan to make it from 3/4 plywood that I have left over from previous projects. What are some helpful features of a good cross cut sled? Thanks Steve
  13. HMH

    Preferred means of sheet/ cut off storage

    So I just came upon a deal for 14 sheets of 3/4" birch ply.....cheap. It was a great deal, so I jumped on it...Now I have 14 sheets of plywood laying on my garage floor. :slap: - shop project priority shuffle - So.....what are your favorite methods of sheet good storage? I'm tight on...
  14. kooshball

    Which flush cut router bit to "cross-cut" walnut?

    I will be cutting the top for my dresser to size soon and but it is too large to safely cross-cut on my table saw. My circular saw is terrible and doesn't have enough support to make a square cut so my plan is to cut close to the final size on the band saw or with a jig saw and then clamp a...
  15. cskipper

    How to cut jigsaw puzzles

    Supplies - picture (one you have permission to use), 1/4" BB or Finnish (similar dimension) plywood, saw blades (FD puzzle blades or 1/0 or 2/0 reverse tooth), some type of adhesive (see discussion below), sand paper, top coat if desired. Steps to cut jigsaw puzzles: There are several...
  16. B

    Rough Cut Walnut $1 / bf

    If I wasn't heading out of town first thing tomorrow morning, I might have a different take on this... Maybe if someone gets most or all of this I can get some of it. I think this is from the same guy that sold the mahogany and the zebrawood. http://raleigh.craigslist.org/mat/2250874684.html
  17. Y

    cross cut sled

    I want to build a cross cut sled for my table saw.I'm concerned about getting it perfectly square with the blade. Any tips?
  18. PChristy

    67.5 degree cut

    anyone got a safe way to cut this angle - All I have to cut it with is a mitersaw
  19. PChristy

    This grass was hard to cut picture framed

    Used two coats of Amber shellac and a coat of BLO - View image in gallery View image in gallery View image in gallery
  20. M

    source for rough cut

    i'm building a barn for my step son and will be needing 220 1x12x10 and 220 1x3x10 also some misc 1x6 and 1x8 16 long leaf southern yellow, dose anyone want to give me a price per bdft and estimate on how long it would take to fill the order? please keep it within an hour or two of moore county.

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top