Menu
Home
Forums
Forum list
Search forums
What's new
New posts
New media
New media comments
New resources
Latest activity
Media
New media
New comments
Search media
Resources
Latest reviews
Search resources
Members
Current visitors
Member search
Social Media
Facebook
Instagram
YouTube
Donate/Pay
Donate to NC Woodworkers
Other Payments
Calendar
Advertise
Pay for Advertisements
Log in
Register
What's new
Search
Search
Search titles only
By:
New posts
New media
New media comments
New resources
Latest activity
Menu
Log in
Register
Home
What's new
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
Latest activity
What's new
New posts
New media
New media comments
New resources
Latest activity
K
Kerrbuggs1
replied to the thread
3way switch wiring diagram with power in and switched leg in the same box
.
Jeff, thank you for sharing this. One of these days, I'll learn to understand electricity a lot better.
31 minutes ago
smallboat
reacted to
Phil S's post
in the thread
Annual Picnic Date revised
with
Like
.
NCWW holds an annual picnic in mid-May. Last year the picnic could not be held safely. This year we will hold a picnic in September...
46 minutes ago
J
jlwest
replied to the thread
DIY Solar Install?
.
You are absolutely correct.
54 minutes ago
SabertoothBunny
replied to the thread
DIY Solar Install?
.
I would recommend that if you do choose to do solar do NOT put it on your roof, EVER. That is worst possible location due to maintenance...
Today at 10:17 AM
Hmerkle
reacted to
Rkadish's post
in the thread
3way switch wiring diagram with power in and switched leg in the same box
with
Like
.
thank you, I replaced a 4 way switch but it was not setup the same as the one I took out. now I have to have one switch on for the...
Today at 10:12 AM
Hmerkle
replied to the thread
3" C-Clamp differences.
.
That makes sense - with a screw you do only get localize pressure.. As for the butcher block tops and stair treads, don't give them any...
Today at 10:12 AM
Hmerkle
replied to the thread
3" C-Clamp differences.
.
Sorry - I will respond as soon as I get up off the floor from laughing so hard! (glad I didn't have a mouth full of coffee!)
Today at 10:10 AM
R
Rkadish
replied to the thread
3way switch wiring diagram with power in and switched leg in the same box
.
thank you, I replaced a 4 way switch but it was not setup the same as the one I took out. now I have to have one switch on for the...
Today at 10:10 AM
Tim Sherwood
reacted to
Henry W's post
in the thread
Dado jig - 'exact width'
with
Like
.
There's nothing 'original' here, I just thought I'd post in case others had not considered such a jig. I suspect others (Joe Scharle...
Today at 10:00 AM
Tim Sherwood
reacted to
bob vaughan's post
in the thread
3" C-Clamp differences.
with
Like
.
Screws don't seem to give me the consistent squeeze-out for a good continuous glue joint. There's a good adhesion area right around...
Today at 9:55 AM
Tim Sherwood
reacted to
bob vaughan's post
in the thread
3" C-Clamp differences.
with
Like
.
Like all goods, there's good and there's bad. The point of this post was to help a buyer make a better informed decision when choosing...
Today at 9:55 AM
Canuck
reacted to
Henry W's post
in the thread
Preferred miter slot router bit?
with
Like
.
Wayne, if you're looking for one, Klingspor's has a top bearing bit in 1/4" shank. as that's what I bought and used (as seen in the pics...
Today at 9:53 AM
R
Rkadish
replied to the thread
Bought a New Leaf Rake Last Night
.
watch for the guys that harvest the pine straw, offer them yours for free and you will not have to rake anymore.
Today at 9:50 AM
H
Henry W
reacted to
Rick Mainhart's post
in the thread
Free Table Saw
with
Like
.
I have a 10" Direct Drive (2 HP!) Sears/Craftsman Model 113.226880 table saw available for anyone wanting a project, or is willing to...
Today at 9:48 AM
H
Henry W
replied to the thread
Some of you may know the long story behind the "Chest of many drawers"
.
Bobby - multiple ideas have been floated in this thread. So it's not clear if your desire to be included is specific to one idea or to...
Today at 9:46 AM
Our Sponsors
LATEST FOR SALE LISTINGS
For Sale Listings - Check out the Facebook page
Started by rcarmac
Yesterday at 8:45 PM
Replies: 5
For Sale / Wanted
Free Table Saw
Started by Rick Mainhart
Yesterday at 4:42 PM
Replies: 0
For Sale / Wanted
S
Powermatic 3520 lathe banjo.
Started by Strom
Yesterday at 11:44 AM
Replies: 2
For Sale / Wanted
Cleaning out the finish cabinet... free to anyone who can use it
Started by creasman
Tuesday at 8:29 PM
Replies: 1
For Sale / Wanted
Oneway #2721 Wood Lathe Tool Rest
Started by Ed Fasano
Tuesday at 11:10 AM
Replies: 4
For Sale / Wanted
Home
What's new
Top