wip

  1. Tiger Maple Hollowform with Holly Pedestal (WIP)

    Tiger Maple Hollowform with Holly Pedestal (WIP)

    • Nate Davey
    • Media item
    • hollowform holly maple pedestal tiger wip with
    • Comments: 0
    • Category: Member Galleries
  2. N

    Tiger Maple HF (WIP)

    The Treasury Department (Mrs Davey), saw a small commercial HF with pedestal and finial at her friends house, and wanted one like it. After looking at it, it was the worst piece of work I've ever seen, and if any of you tell her that I'll swear I never said it. I finished the HF for her today...
  3. Tiger Maple HF (WIP)

    Tiger Maple HF (WIP)

    • Nate Davey
    • Media item
    • hf maple tiger wip
    • Comments: 0
    • Category: Member Galleries
  4. bluedawg76

    coffee table wip

    here's the top for my new coffee table -it's walnut, wormy maple, and cherry. I used some of the walnut with the sapwood streaks in between the maple boards. This was my first attempt at breadboard ends. I learned the hard way that my router fence was not at 90 degrees, which i used to hog out...
  5. Cato

    Jewelry box- WIP

    So after getting this far then I decided to read up on box building, design, and construction. Jeez jumped in head first and from reading Doug Stowe and David Freedman books on the subject I broke a lot of rules, no no's and as usual had to deal with issues because well for one I have never...
  6. mkepke

    WIP - Shaker-style bench

    I'm making a Shaker-style bench to sit outdoors under an oak tree next to my shop. The finished bench will measure 9" x 16" x 86" and is white oak for weather resistance. There are seven parts: the (plank) seat (not shown), two upright legs and four braces. The legs are...
  7. J

    Wine Rack WIP

    Making the Sketch Up design work in the shop. The design. http://www.ncwoodworker.net/pp/uploads/2132/P5110004.jpg Putting together the joinery. Before the leg tapers were cut. After cutting the tapered legs and inserting the end panels. Just about ready for final...
  8. Bugle

    Thought I would give it a shot - WIP

    This all started because I wanted to see if I could hand cut dovetail joints (not easy...I still need to practice). So I built a simple box. (The picture quality isn't very good. I'm not really set up to take good pictures.) Then I decided that I should do something different for the lid...
  9. cyclopentadiene

    WIP Elevated top table with curved tapered legs

    Attached are photos from the dry fit of my latest project. The table is made of walnut. The top is 15 1/2 " x 35" single board elevated 1/2" above the legs and 1/4" from the rails. The legs are tapered in both directions with a slight curve. This was my dry fit which seems to work well. I plan...
  10. erasmussen

    more wip

    I need a thin ring 1/4", gluing up a thin ring is not possible for me maybe some folks can but not me. The good thing is I almost always need them in pairs. So I glue up a normal size ring, this one is holly. And flatten and smooth it on the lathe, as I have no thickness sander ( I have only...
  11. erasmussen

    another WIP

    I havent posted in awhile so I thought I would post a WIP. I am doing a open segment turning, what James calls a snaggle tooth turning. Gluing the first ring on, showing the home built gluing platform. A close up of the business part, with a special built stop block :gar-La; And a...
  12. Larry Rose

    Wip dry fit

    I've been working on this Hepplewhite style dressing table for a few weeks now and finally got to the dry fit stage. I saw one in an antique store last year and was able to get a couple of very poor pics and a few measurements before the store owner started giving me the evil eye. I quess I...
  13. erasmussen

    More WIP

    I am getting in the short row's now got it between centers. Might be able to get the faceplate s off tomorrow. Thanks for looking. A detail picture.
  14. erasmussen

    New WIP the wedding ring

    This is a ring I will use to mate up the top and the bottom of the vessel. The bottom with 2 thin rings unturned. the ring I am going to use, one side is flat and sanded. Spot gluing it on with hot melt glue on the outside. ring turned to the right thickness and sanded flat, the...
  15. leftoflefty

    Cypress coffee table WIP pics

    So I've been working on a coffee table for my sister over the past week. After sweeping all of this up is when I decided I would be purchasing a DC system in the near future. The beer boxes are from watching the NFL playoffs in the shop because the women invaded the den.:wsmile: View...
  16. christopheralan

    Pinewood Derby (Open Division, Dads) WIP...

    Hey guys! This is still a work in progress (attaching weights and wheels), but I had to go for the Michael Keaton Bat Mobile. One of my friends used to work in a car bodyshop, and told me that the finish wasn't good enough unless you could count your teeth in the reflection. I had to go back...
  17. wip

    wip

    wip
    • erasmussen
    • Media item
    • segment turning wip
    • Comments: 0
    • Album: turnings
  18. wip

    wip

    wip
    • erasmussen
    • Media item
    • segment turning wip
    • Comments: 0
    • Album: turnings
  19. erasmussen

    Wip large turning Update

    I aint been being slack mr. Walker (know where that come from), but things have been a bit slow. So I will go ahead and post a WIP its a large turning not huge but large. Got the base started. Cutting segments for one of the rings enough segments for 1 ring sanding the segments...
  20. wip on segmented turning

    wip on segmented turning

    wip on segmented turning
    • erasmussen
    • Media item
    • segment turning wip
    • Comments: 0
    • Album: turnings

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top