wip

  1. IMAG0293

    IMAG0293

    Drum Sander WIP
  2. merrill77

    Coffee Table redux - WIP pics

    I built a prototype for this table last fall - it turned out well enough to avoid the firewood pile but it took forever to finish it. I'm now making progress on this one, which is cherry and padauk. The joinery on this table is somewhat unusual and has been fun, but challenging. This is my third...
  3. Rocky Top Coffee Table

    Rocky Top Coffee Table

    The top is finished and fitted to the stretchers (end view).
  4. Rocky Top Coffee Table

    Rocky Top Coffee Table

    The top is finished and fitted to the stretchers (corner view).
  5. Rocky Top Coffee Table - stretchers in place

    Rocky Top Coffee Table - stretchers in place

    Here are all 6 stretchers in place
  6. Rocky Top Coffee Table - sliding dovetails

    Rocky Top Coffee Table - sliding dovetails

    This picture shows how the 4 short stretchers join to the tops
  7. Rocky Top Coffee Table - planing edge profile

    Rocky Top Coffee Table - planing edge profile

    I removed most of the waste on the table saw and then finished the profile with a plane.
  8. Rocky Top Coffee Table - planing end profile

    Rocky Top Coffee Table - planing end profile

    Planing the profile on the end of the tops.
  9. Rocky Top Coffee Table - cutting the curve on the ends

    Rocky Top Coffee Table - cutting the curve on the ends

    The ends of the table have a slight curve to them. I roughed it out at the bandsaw, to be cleaned up with a plane.
  10. Rocky Top Coffee Table - roughing out the end profile

    Rocky Top Coffee Table - roughing out the end profile

    Roughing out the profile on the end of each top piece. I did this by eye, no jigs - just roughing it out and will finish up with a plane.
  11. DWSmith

    Maple Island WIP

    I have an order from a restaurant in NJ for this island. The hard maple top is 24" x 48" and 8" thick and weighs a ton! The base is also hard maple, the legs are 3 3/4" square and the aprons are 6" wide. All the exposed edges on the legs and aprons have been beaded to get rid of sharp edges and...
  12. nelsone

    Lazy Susan WIP

    Making a few of these for Christmas presents. Nothing like cutting it to the last minute! Should finish up tomorrow. View image in gallery
  13. erasmussen

    WIP update open segment

    I was sick for a few days and didnt get to the shop. I finally got back, got all the knobs knocked off, sanded, and started putting finish on it. After I get some finish on it then I will still have to turn and finish both ends.
  14. erasmussen

    Top half WIP

    The top half in work now, starting the build up on the brute and using the HF lathe to clean the rings up (I am still using the HF lathe). Dont look at the mess in the shop. Got to keep my tools sharp, real sharp for this. IPE cuts easy, this is the shavings First row of open...
  15. rcflyer23

    Pie Safe WIP - Small Update 5/6/12

    I came into some oak last month and have begun the process of turning it into a Pie Safe for the wife. I also had some Spalted maple that was give to my dad and I by PChristy that I finally got around to milling up and using. I'm using it for the panels in the pie safe and I'm also using it...
  16. J

    Dual Purpose Post - WIP and Dust Collector vs Cyclone Attachment

    So, I have two goals with this post. 1. I've been working on a walnut toy box. This is my first project using rough lumber. Pictures below: Rough cut from Saw4you: Squared Stock Dry Fit of the front face - first raised panel project 2. During this project, I managed to create a giant...
  17. S

    36" bandsaw restoration (WIP), more PICTURES!

    .
  18. Larry Rose

    WIP Campaign Table

    I saved the plans for this British campaign table from PWW mag. a couple of years ago. This is the dry fit. I'll start the sanding and assembly today. It's mahogany and I quess it's really just a 18th century TV tray. View image in gallery
  19. PeteM

    Grotesque carving WIP - Done 11-26

    I had my camera out so I thought I'd post a WIP pic. This is my first attempt at carving "in the round". So far I'm pretty happy with how it's coming along but I have plenty of time left to mess it up! pete
  20. M

    Barbie House Storage Dresser - WIP

    I started a thread in the finishing forum about 'Stain Options on Hickory (Pecan)', http://www.ncwoodworker.net/forums/showthread.php?t=41004. But at this point, I thought I would continue over here as a Work-In-Progress thread. My daughters have a Barbie house with loads of pieces and parts...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top