plywood

  1. M

    Looking for Cabinet grade Oak Plywood near Monroe

    Anyone know of a supplier on the east-side of Charlotte? Do not want Lowe's or HD, and I want to avoid going all the way to Wurth.
    • Matt Furjanic
    • Thread
    • cabinet grade monroe oak plywood
    • Replies: 1
    • Forum: Wood
  2. kooshball

    Dresser carcass wood design, plywood or secondary hardwood (wood movement issue)

    I am still in the final planning stages with my next project, a wide walnut dresser. I plan to use vertical grain solid walnut sides joined to the top and bottom carcass with half blind dovetails. I was originally planning to use plywood for the top and bottom carcass since it is quick and is...
  3. Botanist

    1/8 inch Red Oak Plywood

    I am looking for a quarter or half sheet of 1/8 inch red oak plywood. Is there a local source in Raleigh/Durham? I can go a 1/4 inch if I have too. Thanks, Ron Johnson Durham
  4. manfre

    1/32" plywood in the triangle?

    Are there any stores in the triangle that sell 1/32" plywood. Some hobby shops sell 12" x 24" sheets of birch for making planes, but I haven't had any luck finding one. Ideally, I'm looking for a few sheets of 1/32" walnut.
  5. J

    1/2" Birch Plywood

    Some of the HD stores are now stocking either, or both birch and red oak 1/2" ply, in addition to the 3/4" stuff. Priced at about $42 for a 4 X 8 sheet. This is NOT baltic birch, but regular birch plywood made by Columbia Forest Products in Old Fort NC. I bought a sheet today to build a shaker...
  6. Bas

    Small pieces of 1/4" cherry plywood

    I need two pieces of 1/4" cherry plywood, 12" x 18" each. I can order this from Rockler of course, but are there any local stores that sell something smaller than a full sheet?
  7. L

    Quartersawn oak plywood

    I'm a newbie, located in Hendersonville, about half way between Asheville and Greenville, SC, and I'm looking for a source of quartersawn oak plywood. Any suggestions? I'm not a volume used, just 2 or 3 sheets at a time.
    • Larry H
    • Thread
    • oak plywood quartersawn
    • Replies: 1
    • Forum: Wood
  8. S

    Cherry Plywood

    I am creating a wood desktop and I used cherry on the edges and cherry plywood in the center. But when I sanded the cherry plywwod it removed some of the cherry top and now I am left with plywood in some areas. Is there anyway to fix this or do I need to start over?? Thanks in advance for your...
  9. B

    Walnut edge on oak plywood

    I am building a new top to an exising podium which is made from red oak 1 X 2 frame and oak plywood panels. The actual top will be oak ply with a walnut band. I have some Golden Oak Danish oil that I know will make all the oak parts match the rest of the podium. I am thinking that I don't...
  10. J

    5/8 cabinet grade plywood

    Need to find 5/8 cabinet grade plywood. in raleigh area Thanks Dwight
  11. gcgarner

    Cool clip about making plywood in Old Fort

    Thought some of you might find this Discovery Channel clip interesting ... http://www.youtube.com/watch?v=hH86eahxeq8
    • gcgarner
    • Thread
    • clip cool fort making plywood
    • Replies: 1
    • Forum: Wood
  12. CrealBilly

    Rift Cut SYP Plywood

    Looking to make some kitchen cabinets - wifey wants pine of all things, country look, saw a picture in a magazine :roll:. I'm looking for a source for 3/4" pine rift cut plywood so I can start figuring how much this project is going to cost me. Not the warped flat cut junk they sell at the BORG...
  13. scsmith42

    Plywood recommendation

    I'm not much of a plywood person; have used solid wood for all of my projects to date. However, it's time for me to "go over to the dark side".... and I could use some advice. If you were going to obtain some plywood to have on hand for general shop use (jigs, fixtures, etc), what type of...
    • scsmith42
    • Thread
    • plywood recommendation
    • Replies: 11
    • Forum: Wood
  14. BKind2Anmls

    Cabinet Grade Plywood

    A man in Harrisburg, NC advertised cabinet-grade, 3/4" plywood for $27 per sheet. He says he has a couple hundred sheets. Before I drive three hours to go get 20 sheets, is there anyone close who can go by and see if it is good stuff? Please PM me and I will send you his number. He told me he...
  15. L

    Birch/Red Oak Plywood (Not stolen!) Winston Salem CL

    Not mine, etc. Looked tempting http://greensboro.craigslist.org/mat/1803765779.html
  16. C

    finishing bad plywood

    I just built new bathroom cabinets using oak face frames and oak plywood for the box. When testing wipe-on stains for color, I noticed the plywood isn't taking the stain evenly, even when using a sealer before the stain. (yes I bought chinese plywood from Lowe's - i've learned my lesson) It's...
    • Curtis
    • Thread
    • bad finishing plywood
    • Replies: 10
    • Forum: Finishing
  17. taandctran

    where can I find some osb or plywood siding???

    I'm going to build my kids a playhouse for Their birthday. I want to put plywood siding or osb siding on the exterior, so the exterior will be a "one step" process. Anywhere know a place to buy this stuff that is cheaper then lowes or Home Depot? I think they want around $15-$20 for it there...
  18. L

    Maple 3/4" plywood $69-->$39 at HD NW Greensboro

    At least a dozen sheets left of some really nice maple plywood at the Brassfield Home Depot in NW Greensboro - I bought a couple of sheets since I couldn't pass on the markdown... cut well, looks good, no voids on the few cuts I did, and seems quite flat/unwarped. Not sure if on clearance...
  19. C

    Warped 1/4" Plywood

    I have some birch 1/4 plywood that warped slightly due to the heat in my shop. I was wanting to use it for paneling on cabinet doors. The cabinets will be painted white so I am using birch panel with 2" styles and rails (with a grove down the center to accept the panel). I cut the panel to...
  20. L

    Walnut or Walnut Plywood

    I'm making a wall of bookcases for the mancave. Most of the plans I looked at included mostly plywood. They said it would be more stable and cost less. I thought I would save some money and use walnut plywood for the case and walnut for the trim. So I bought a couple of sheets of walnut plywood...

Premier Sponsors

Contact for your financial processing needs!

Our Sponsors

LATEST FOR SALE LISTINGS

Top