plywood

  1. A

    Project: JetSki Shop Stand

    Hello NCWW community, I wanted to seek your advice in regards to material choice for a project I am working on. I have designed these interlocking stands that can be routed out so they can be assembled without tools. My question is in regards to strength and choosing the correct material...
  2. charlessenf

    Source Needed for "Pre-Finished (2-sides) Maple Plywood" in Lenoir, NC Area

    I've been searchin' the web with little success. Lowes was not helpful. Home Depot sells 4x4 and 2x4 panels but says it can't order 4x8's (though its supplier - Columbia - sends one to HD!. I am looking for that stuff with the clear, very durable, finish on both sides and a sheet or two with...
  3. Absinthe

    work bench/table and holdfasts

    Hi, I am just setting up my shop now that I have the room to do it. First thing I did was make 2 work benches/tables to give some flat surface area and additional storage. They are both the same 2'x4', 2x4 construction with a "top" and a bottom shelf. I just finished cross bracing and...
  4. Bamboo_x

    Bamboo_x

    RGB LED Built in cabinets made out of Plyboo
  5. Bamboo_x

    Bamboo_x

    RGB LED Built in cabinets made out of Plyboo
  6. Bamboo_x

    Bamboo_x

    RGB LED Built in cabinets made out of Plyboo
  7. Bamboo_x

    Bamboo_x

    Built in cabinets made out of Plyboo
  8. Bamboo_x

    Bamboo_x

    Built in cabinets made out of Plyboo
  9. Bamboo_x

    Bamboo_x

    Built in cabinets made out of Plyboo
  10. Lumber and Plywood Purchase

    Lumber and Plywood Purchase

    Lumber I purchased from the Hardwood Store of NC
  11. E

    local curved plywood suppliers?

    Has anyone come across a local (NC) supplier of 1/2 or 1/4 round curved plywood. I'm looking for 12" radius 5/8 - 1/2" thick. Edit: here is a non-local supplier of what I'm looking for http://www.bd-international.com/Curved.htm
  12. R

    Extra long plywood for cabinets

    I am building cabinets and I need a couple sheets longer than 8 feet to avoid a joint. Does anyone know where I can pick up 10 foot sheets near Charlotte? I'm planning to paint them but I'd like to have decent quality because I plan to use them for the cabinet tops. The only other thing I...
  13. K

    formaldehyde free maple veneered plywood for cabinets

    I'm looking for formaldehyde free 3/4" maple faced plywood to build some cabinets in my home. I checked the hardwood store in gibsonville. They have some low-formaldehyde stuff, but thats it. I know that Home Depot sales the purebond formaldehyde free stuff with baltic birch and oak veneer...
  14. zapdafish

    3/4" x 7" x 7' wide plywood strip

    I am hoping someone has a left over piece of 3/4" plywood in the Raleigh area that will provide 1-2 pieces, about 7 inches wide, about 6.5 - 7 ft long. I only need 1 but wont mind a backup piece. Willing to pay 1/6 - 1/3rd of the value of the plywood sheet depending on how many pieces are...
  15. Bill Clemmons

    Need plywood software

    Does anyone know of a FREE software program that lays out a sheet of plywood to optimize cutting and utilization? I thought I had one bookmarked, but I can't find it. Thanks Bill
  16. D

    Bamboo plywood in NC?

    Anyone know of a source for 1/4" bamboo plywood in NC? Thanks!
  17. J

    Melamine coated vs. Phenolic coated Plywood

    Are these the same beast? Have you used one or the other and purchased it locally? Cost for 1/2" or 3/4" per 4' x 8' sheet? :dontknow: 1/4 sheet (2' x 4') of 1/2" thick phenolic is about $50. Ouch and yikes...
  18. AmishWarlord

    Cedar plywood

    Anyone know a source for cedar plywood near Charlotte? Looking for 2, 1/4"X4'X8' panels
  19. Cutting Table For Plywood Sheets - the table corner

    Cutting Table For Plywood Sheets - the table corner

    I took this photo to show the saw kerfs in the top of the table. These do no harm anything as they are all shallow. When the table finally gets too many of these I'll make a replacement table top and transfer the legs to it.
  20. Cutting Table For Plywood Sheets - HDPE guide

    Cutting Table For Plywood Sheets - HDPE guide

    You can make this piece to fit whatever brand of straightedge you may have. Mine, both the 4' and 8' came from Peachtree Woodworking in Atlanta. They are both identical except for the length and they lock in place from underneath much like the other straightedge clamps on the market.

Our Sponsors

LATEST FOR SALE LISTINGS

Top