plywood

  1. D

    2'x2'x1/8" plywood in Raleigh?

    I need a piece of 2'x2'x1/8" stain grade plywood for the back of a shadow box for mineratures. Anybody know a place in Raleigh to get a small piece like this? I wonder if the new Woodcraft will have it when they open? I have some 1/4" mahogany plywood that will work if I can't find any...
  2. L

    Construction of cabinets with 1/2" plywood

    Here I am looking for help again from the experts. As you remember I completely remodeled my kitchen with 3/4" blond plywood and cherry faceframes. I have a utility room cabinets that now needs to be replaced. I have extra birch plywood that I would like to use however it is 1/2". I know...
  3. B

    Dovetailing 1/2" plywood?

    Status: Entered Assigned To:: Unassigned ===================================== Using the Porter Cable Dovetail Jig, need a solution to avoid the destructive plywood splintering I am getting. I am using good grade plywood (specifically 1/2"). . . do you think applying titebond glue to ends will...
  4. V

    where to buy oak plywood in Raleigh?

    Hi, Where is the best place in the Raleigh area to buy reasonably good quality red oak plywood at a fair price? Lowes is closest, but do other places have either better quality and/or lower prices? Thanks, Gregg
  5. L

    Construction of 1/2" plywood drawers

    I would appreciate suggestions for 1/2" plywood drawers. I will add a false front of red oak once the drawers are glued up. Thanks Lorraine
  6. L

    1/2" plywood usage

    If you had 10 sheet of 1/2" birch plywood what would you do with it? I have seen many applications for 3/4" from cabinets to furniture. I know all about faceframes with 3/4" but can't quite see the use of 1/2". Any thoughts? I would like to see the application with furniture or maybe cabinets in...
  7. RobD

    Plywood Mart in Charlotte

    I drove by it the other day on South Blvd, just south of the Home Depot center with the Klingspors. Has anyone ever been there or know if they sell cabinet grade plywood? Do you know if they are open for woodworkers or just contractors? Thanks.
  8. T

    Verticle Plywood Storage

    I posted a thread June '06 about plywood storage. I have finally gotten around to designing and building a wood storage system. Following advice from the forum experts, I viewed DL's system shown below. It is a cool design. It is hinged and swings around for access. :icon_thum My question is...
  9. Travis Porter

    QSWO Plywood

    I went to Steve Wall today and spent too much money, but I did buy some shop grade plywood. I had to stop the guy from loading it as I had to question whether it was shop grade or not. 3/4" ply and what looked perfect to me without any defects and it was QSWO for $39 a sheet. That beats the...
  10. WoodWrangler

    Russian Birch Plywood 18mm - $3 ???

    What is "Russian Birch Plywood" and is it any good? That is one heck of a price!
  11. BobN

    Wanted-Red Oak Plywood

    I need 2 sheets of 1/4" Red Oak Plywood, Plain Sliced, Good both sides. I have not been able to find any and have not been able to find anyone that would order it for me. Bob
    • BobN
    • Thread
    • oak plywood wantedred
    • Replies: 7
    • Forum: Wood
  12. T

    Assistance Locating Marine Grade plywood

    Evenng all, I could use some assistance with this. Looking for 3/8"-1/2" thick, 8'-10' long, 3'-4' wide....need to do some rework on the old boat. Would be great if you know a place not too distant a drive frm the Raleigh/Durham area, but it is what it is.... Any assistance greatly...
  13. L

    Faceframe for red oak plywood chest of drawers

    I have put my kitchen remodel on hold to take a break. I have a red oak chest of drawers that I started with my brother several years ago that I would like to finish. It is a Norm Abram pattern, I have lost the plans and can't find them on his site. The sides and rails are all plywood. The...
  14. Jon

    Cabinet grade plywood and 3/4 stock

    I live in Winston Salem and was wondering where I can get Cherry and cherry Plywood. Is there anywhere local? I dont mind driving to get it I just cant find any anywhere.
    • Jon
    • Thread
    • 3 or 4 cabinet grade plywood stock
    • Replies: 6
    • Forum: Wood
  15. alleng

    Mitering Birch Plywood

    I am cutting birch plywood and am getting a lot of splinters on the edges...just wondering which would make a cleaner cut...a miter saw or a table saw. I am cutting 45 degree angles to make a mitered corner on a box. Any suggestions, please?:eusa_thin
  16. striker

    Marine Plywood

    My brother is fixing to build a small skiff. He lives in the Mooresville area and is looking for a supplier for 1/4 & 3/8 marine ply in the Charlotte area. Since I'm on the other side of the state I'm not familiar with suppliers in that area. Do any of you folks know who carries marine plywood...
  17. ebarr

    Advice on 3" holes in 3/4 plywood

    What would be your advise on drilling 3" holes in 3/4 in plywood. Forstner bit or Hole saw. Keeping in mind that this may end up being quite a few holes. Let me explain... I am orignally from southern Indiana. Growing up we played a game called "Washers", this is very similar to Horseshoes...
  18. Douglas Robinson

    Resources and prices for Baltic Birch plywood

    I was wondering what people have been paying for 3/4" 4'x8' Baltic Birch veneer plywood sheets, and where they have been purchasing it. Doug
  19. T

    Warped Plywood

    Ok, I go to a reputable wood dealer buy nice 3/4 plywood. Bring it to the shop, store it flat, cut it up and notice that it is bowed or warped. This happens frequently. Is it something that I have to learn to deal with? Am I doing something wrong? or what?:oops: Thanks
    • Travis
    • Thread
    • plywood warped
    • Replies: 15
    • Forum: Wood
  20. M

    New Type of Plywood mentioned at TWA Meeting

    At yesterday's TWA meeting in Raleigh, Bruce mentioned a new type of plywood that he had run across. If Bruce reads this or if anyone recalls, can you recount the details? I thought he said that he found this new plywood that was pretty inexpensive with fewer voids. Unfortunately, I didn't...
    • MarvinWatkins
    • Thread
    • meeting mentioned plywood twa type
    • Replies: 16
    • Forum: Wood

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top