square
-
MDF Square
- SteveHall
- Media item
- mdf square
- Comments: 0
- Category: Member Galleries
-
try square
Wooden try square made from odds and ends of wood left over around the shop. The grip is mahogany, the blade is QS beech, and the pins are walnut dowels.- Charlie Buchanan
- Media item
- hand shopmade square tools try
- Comments: 0
- Category: Smaller Woodworking Projects
-
try square
Wooden try square made from odds and ends of wood left over around the shop. The grip is mahogany, the blade is QS beech, and the pins are walnut dowels.- Charlie Buchanan
- Media item
- hand shopmade square tools try
- Comments: 0
- Category: Smaller Woodworking Projects
-
D
Just a little square walnut bowl
I turned and finished this little fella in about 4 hours yesterday. It was good therapy and cheaper than seeing a Shrink! The top is 4 3/8" square. Height is 2 1/8". Polished to 2000 grit. Finish is.....(wait for it.......) Walnut oil !- Dave Peterson
- Thread
- bowl square walnut
- Replies: 6
- Forum: Woodturning
-
Try Square Spalted Wormy Maple
Spalted Wormy Maple & Walnut- Rick M
- Media item
- maple spalted square try
- Comments: 0
- Category: Smaller Woodworking Projects
-
Try Square Spalted Wormy Maple
Spalted Wormy Maple & Walnut- Rick M
- Media item
- maple spalted square try
- Comments: 0
- Category: Smaller Woodworking Projects
-
Try Square Spalted Wormy Maple
Spalted Wormy Maple & Walnut- Rick M
- Media item
- maple spalted square try
- Comments: 0
- Category: Smaller Woodworking Projects
-
Interesting square
I must need this...don't I?:gar-Bi http://www.modifiedsquare.com/- Bugle
- Thread
- interesting square
- Replies: 9
- Forum: Hand Tools and their Use
-
Am I slipping back into the square world?
One of my students wanted to see how one goes about turning a square bowl they had seen on the net so I did this one for a demo for the class. It is the first square bowl I've turned but wasn't much different from the some Tea Light holders I made last month, just on a bigger scale. It is...- flyrod444
- Thread
- back slipping square world
- Replies: 2
- Forum: Woodturning
-
holdfast in square vs round holes - unscientific test
My Gramercy holdfasts from Tools For Working Wood arrived yesterday. I had already build a tiny workbench surface for testing. It is 2 7/8" thick with a round hole and two square holes. One of the square holes is 45deg to the other - I am curious if the angle has any effect on holding power on...- merrill77
- Thread
- holdfast holes round square test unscientific
- Replies: 10
- Forum: Hand Tools and their Use
-
Square end scraper magnetized?
I just bought a Crown square end scraper. As I started to use it today I noticed it would snap down on the tool rest like a magnet. It was strong enough that you had to pull up slightly to break it free. I need to know how to demagnetize it.- Tommy Smith
- Thread
- end magnetized scraper square
- Replies: 2
- Forum: Woodturning
-
holdfast in square vs round holes - help me test?
A while back I asked about using a holdfast in square holes, since I've seen varying reports. I asked Gramercy, and they said square holes won't work but one or two people here said they work fine. Someone also suggested testing it myself. I initially dismissed that suggestion, but I'd like to...- merrill77
- Thread
- holdfast holes round square test
- Replies: 9
- Forum: Hand Tools and their Use
-
next holdfast question - square holes?
Another newbie holdfast question... My searches have turned up a few people saying "holdfasts will not work in a square hole" but few of those appear to have actually tried it. Roughly an equal number saying "they work fine for me in square holes". Nothing either way too definitive. Christopher...- merrill77
- Thread
- holdfast holes question square
- Replies: 12
- Forum: Hand Tools and their Use
-
busted routing jig
- eyekode
- Media item
- dog hole square strip
- Comments: 0
- Category: Shop Photos
Premier Sponsor
Our Sponsors
LATEST FOR SALE LISTINGS
-
-
Graco 395 FinishPro air assisted airless sprayer for sale
- Started by RobH
- Replies: 1
-
-
-