leg

  1. S

    Delta BS150LS 10' Band Saw with Leg Stand - $175 (Raleigh, NC)

    Not Mine http://raleigh.craigslist.org/tls/2182057647.html Delta BS150LS 10' Band Saw with Leg Stand - $175 (Raleigh, NC) Date: 2011-01-26, 7:12PM EST Reply to: sale-hfgeh-2182057647@craigslist.org [Errors when replying to ads?] I have a Delta Shopmaster 10" Band Saw with Leg Stand...
  2. Hinged support leg

    Hinged support leg

    Basic scetch of a hinged support leg for the TS outfeed discussion.
    • manfre
    • Media item
    • hinged leg outfeed support table
    • Comments: 0
    • Album: Misc
  3. danmart77

    Walnut Desk/bookcase: final leg

    My last post was some notes on the desk gallery. Here are some shots of the desk with the locks installed and brass mounted. Upper bookcase done. You can see more photos in the gallery under danmart77 if you're curious. Its still in Durham but like its big sister it will be gone soon. dan...
  4. eyekode

    Wood screws: Moxon double screw vise and thread for leg vise

    Thanks to Tom (toolferone) I got the chance to use a Beall wood threading kit like this one: http://www.bealltool.com/products/threading/bigthreader.php Pretty cool kit. Especially the tap that has a guide in front of the threads to make sure you are taping in line with your pilot hole. First...
  5. farmerbw

    Single Leg attachment suggestions

    I'm making a couple of fairly simple portable tables from some free plans that I'm going to enlarge and think I need to deviate from their suggested mounting hardware and am not sure what I should use. The top is just a 3/4x11 3/4x19 1/2 ERC plank that will have some holes and slots to hold...
  6. adowden

    QS leg question

    I want to make a Arts and Crafts end table with quartersawn legs. I would like the legs to have quartersawn figure on all four sides. The method I want to use is gluing up two or three QS oak boards with QS figure on their width and then gluing thin (1/4") QS oak over the visible edges on both...
  7. kooshball

    Bed leg design and construction help needed

    This question came about on my previous post on the "wood" forum regarding 16/4 walnut but I figured that I would put it here for more traffic. I am going to build a bed out of walnut and the legs are 3" x 3" with a slight taper on the inside of an otherwise square leg. Something like this...
  8. WoodWrangler

    How do you cut a 4-Way Taper Leg

    I've cut a two-way taper leg, but now I'm need of a four-way taper. Any tips or suggestions on how to pull this off safely?
  9. CrealBilly

    Chicken broke his leg?

    I think the shop crawl chicken might have broke his leg cause he ain't walking anymore, or does it have something to do with "eat BBQ!!!"
  10. Jim Murphy

    Splayed leg table

    After spending a couple of fun-filled months in the shop making these I needed something to fill my time and mollify the need to actually build something. So, after a lot of deliberation, and making a prototype from old pine studs, I created this: There will be ample room on the table...
  11. S

    cabriole leg ??

    I am just before starting my first cabriole legs. They will go on a small display table, approx. 26"x14". Everything is cut out except for the legs. I have made, cut out, and sanded the pattern to the shape I like. Everything I've read about cabriole legs says to start with square stock and...
  12. froglips

    More refinishing spindle leg tips.....

    Yet another tip. History, stripped and refinishing a drop leaf table for the LOML. Prob? 6 legs and 8 stretchers, all turned. Beads, coves, the whole nine yards. The stripper did a good job, but ever try to sand spindles off the lathe..... A FREAK'N NIGHTMARE. In the end, here is...
  13. Kdub

    busted leg

    one year ago i started the windsor chair class with walnutjerry so here i am working on three more chairs and this looks like a little bump in the road for me. does anyone have insight on what might have caused this? i have my theories but i'd like to hear some of yours. i was in the process of...
  14. L

    Help with tenon cut for trestle leg

    I am ready to cut the tenons for my trestle legs. If you remember I made these legs a short time ago. My cut wasn't exact when I finished and prepared it for glue up so I hope someone can help me learn a better technique this time. I used the dado blades in my tablesaw, the fence on the right...
  15. Legs Folded Up

    Legs Folded Up

    To fold the legs up, remove the Locking Knobs and swing the legs assembly to the right.
    • KC7CN
    • Media item
    • 64a fold-up leg outfeed powermatic support table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  16. Leg Hinge & Locking Knob

    Leg Hinge & Locking Knob

    The 5/16'' hinge bolt is attached to 1-1/4'' angle iron used for mounting out-feed table. Locking knob is a lawnmower handle replacement knob, epoxied to 5/16'' threaded rod. Keywords: PowerMatic 64A Fold-up Outfeed Table Tablesaw Support Leg
    • KC7CN
    • Media item
    • 64a fold-up leg outfeed powermatic support table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  17. Fold-up Support Legs

    Fold-up Support Legs

    Outboard support legs are required to accommodate additional weight of extension table, accessory drawer, and outfeed table. Remove two locking screws to fold the legs up to move the saw.
    • KC7CN
    • Media item
    • 64a fold-up leg outfeed powermatic support table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  18. nelsone

    Cabriolet Leg Question

    I have a small table that I'm planning to build and I'm trying to work out some design ideas in my head. I would like to use cabriolet legs on the front and was wondering if you guys use solid stock for that style or do you laminate smaller stock?
  19. New Leg

    New Leg

    It was easier to replace the entire leg than to replace the missing foot. A circular saw was used to cut a groove on the face of the old leg, and a chisel to remove it. The old glue joints were easy to break apart.
    • KC7CN
    • Media item
    • antique dresser dumpster leg new
    • Comments: 0
    • Album: Dumpster Dresser Rescue
  20. J

    Banquet table leg sets

    :eusa_clap Made a trip over to State surplus today. They had the usual desks that would make an outfeed table. Also there was a pallet of folding tables for $5.00 each. If you have ever wanted to make a sacrificial table for breaking down plywood with circular saw, this is the way to go. Also...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top