cut

  1. C

    Looking for some rough cut

    Hey all New to the community here! Just wondering where I might be able to find some rough cut timbers for a beam cieling project that I am considering. 7x9 being the main beam. I live in Ash,nc so anyone know where to find odd sized beams like these. rough cut for the rustic look. thanks all...
  2. J

    5/4 hickory and ask rough cut

    Looking for someone who stocks both items in the rough as close to Wilmington as I can get. I can get Ash in Elizabethtown but no luck with Hickory yet. Thanks for any help.
  3. PChristy

    Should not have cut this but.......

    did it anyway - I really did not have the correct blade to cut this IMHO - I cut it with a #3RFD - I think I should have had a least a #5 - plus I do not have the correct sanding method to get the sides smooth as you can see from the side shot - This pattern has alot of sharpe corners where you...
  4. NZAPP1

    My first stack cut

    This is my first stack cut. Thanks for looking
  5. G_ville_worker

    Cross Cut Sleds

    I've been looking at several crosscut sleds with the miter fences. It seems that a lot of pictures always show the sled to the left of blade. Dubby, Rockler, etc. It would seem to me that you would want one on the right side of the blade so you can bring the blade to 45 degrees. If it was on...
  6. D

    Cut another one down

    Brian, Greg, and Robert...... Cut that "next victim" down this morning. Not sure but it looks like red oak; just doesn't have that usual smell of red oak. As I was cutting into it, a literal waterfall came out of the cut. Looking at the wedge I cut out to direct the fall, you'd swear I cut a...
  7. christopheralan

    So how do you cut a rabbit?

    Just wondering on this one. Do you cut a rabbit with a sac. fence, or cut it with the rip fence away from the dado stack? Why? I do both, just asking the crowd.
  8. S

    hand cut 18 inch x 10 inch x 40 foot mortise

    .
  9. MikeL

    Need help with bandsaw blade cut leading outward???

    I have spent the last 3 hours scratching my head trying to figure this problem out. Does anyone know what might cause a bandsaw's cut to lead outward? I have tried adjusting the roller guides to the manufacturer's recommendations. I reset the blade to sit on center, adjusted the tracking and...
  10. Mark Stewart

    Angle cut on table saw

    Well here is my delima. I watched the guy at the ww show turn a kilidiscope but he never talked much about the cuts of wood. It requires 3 ea 10 1/2 by 2 1/2 with a 30 Degree angle cut down both sides of the length of all three pieces. I also must keep the top at 1 and 3/4. to make a triangle...
  11. 6

    Where to buy rough cut boards (pine/utility?)

    I am installing a ceiling for a basement and am looking for some rough cut boards. I am looking for cheap and rustic. Looking for... Amount: 1500 square feet (includes 30% extra) Type: Pine is fine (and I believe the cheapest), but I am open Width: varying Length: varying Thickness...
  12. skysharks

    Interesting Cut offs

    Sometimes you end up with really interesting cut offs from your work. Even these scraps can inspire another project. Book Ends, maybe:dontknow::icon_scra:eusa_thin
  13. jonnyfontaine

    to cut or not to cut, part deux

    ok... this time i am writing to see if it is better to cut dried wood, or leave it in it's current state untill ready to use? i have some 8/4 and 6/4 slabs that are about 8" wide and 24" long, and they will eventually be resawn into bookmatched pieces and i sometimes get too antsy and wanna see...
  14. jonnyfontaine

    green wood, cut now or wait till dry

    i have bought some green wood, not sure of the exact MC, but i am eventually planning on resawing the 1" thick board into a bookmatched set 3/8" thick... should i wait for the wood to season or should i resaw the wood and then sticker it to dry before use... i figure it would dry faster as...
  15. L

    Question concerning cut on rail

    I am about to cut an inch cut on the bottom edge of a rail so that it can fit into a base. The instructions say to avoid chipout, first cut the shoulders with a crosscut blade. Does that mean to use the rip blade and make the cut one inch from the bottom and then use the dado blades for the...
  16. J

    When is an off cut a scrap, or worse garbage ?

    Lefty Tom's recent post about making a planer cart out of scraps got me thinking..... At what point do you decide that an off-cut is a scrap, and then when that scrap is garbage ? I've been doing a little straightening up of my shop (much needed) for the upcoming shop crawl and have been...
  17. A

    My buddy Brent's hand- yes a *PIC* (Warning graphic cut)

    You may remember my buddy Brent in VA telling about his run-in with the Byrd Shelix cutter on his 12" Bridgewood jointer two weeks ago. Though not back at work, he is getting better:
  18. WoodWrangler

    Cut & Sand in one step?

    A buddy of mine came across this ... I had never heard of it. Have you? http://www.finalcutblade.com/finalcut_videos.php Seems that would be a problem on a good quality carbide blade because the teeth are actually wider than the metal of the blade (thus after the cut the a gap would exist...
  19. taandctran

    rough cut AMBROSIA MAPLE bowl blanks

    I have alot of ambrosia maple wood that I am going to cut into rough cut bowl blanks. most of these are good size, but I do have some smaller ones. I am going to sell them sealed for around $5 or maybe alittle more for the biggest ones. THESE ARE ROUGH CUT AND GREEN. BUT WILL BE SEALED. I...
  20. Bryan S

    Measure twice cut once. I did, but.....

    Nowhere does the cliche say to make sure your panels don't move when routing dados. If so this is what you get asymmetric parrallel dadoes. :BangHead::BangHead::BangHead:. Fortunatley this is an area thet will be covered by a filler strip underneath and drawer slides above. I was able to...

Premier Sponsors

Contact for your financial processing needs!

Our Sponsors

Top