wrong

  1. PChristy

    Is it wrong for me to ....

    like to turn Acrylic pens more then I do wood? I have tried and tried to get some decent looking wood pens but I just can seem to get them to look good - Don't get me wrong I do like my wood but I just can't get them to turn out the way I would like for them to be - I told my wife to day that...
  2. CrealBilly

    I'm in the wrong business

    130.00 plus S&H in oak / 115.00 plus S&H in pine or buy the plan for $9.00 Wife want's 2 - do you think I'll need to purchase the plan, I don't know it looks pretty hard... and beside I have no idea what the measurements are :icon_scra What kind of new tool could I get out of this project...
  3. PChristy

    Must be doing something wrong

    Correct me please - I sand my piece up to 12000 using the MM - when I put the CA finish on I put BLO on then I apply the CA - repeat - repeat - use the 12000 only - BLO-CA repeat- repeat- Up to ever how many coats I want to have - I only applied four to this BW - am I doing this correctly - so...
  4. Bas

    What's wrong with this construction?

    View image in gallery
  5. Tar Heel

    Wrong year in WoodWorks ad

    The year shown is 2010.
  6. Ken Massingale

    There Has To Be Something Wrong!

    How can this place sell Euro/Designer pens, segmented, for $4.00 and include laser engraving???? (Bottom of page) The kits cost almost that price. http://www.wplaser.com/Wood_Pens.html?gclid=CNDF0LjX-poCFRUhnAodd0wfdg :kamahlitu
  7. PChristy

    What am I doing wrong guys???

    The last few bowls I have turned I tried using a jam chuck that I made out of a piece of Dogwood = I made it round - rounded off the edges on the end - I seen where some ppl use leather on the end and I have seen some use sand paper put in between the chuck and the bowl for gripping - I have...
  8. Douglas Robinson

    Wrong Forum

    This thread is in the "how to" forum: http://www.ncwoodworker.net/forums/f101/adding-short-video-clip-post-21666/ It should be somewhere else.
  9. dancam

    [Problem-Main Site] Is something wrong?

    Is there something wrong with the site? It is taking over 30 secs for the site to load and when I surf through to the forums it also takes an inordinately long time. I'm not having problems with any other websites. Thanks, Dan C.
  10. rcflyer23

    Please tell me what I am doing wrong!!

    So being a new woodworker I don't know exactly how to use all the power tools and my new jointer is one of them apparently. I was running some wood through it today and yesterday trying to figure out how to use it and just to get to know it and ever time when I get to the end of the piece it...
  11. TracyP

    What is wrong with me? Jeff.....

    Went to Woodcraft today and spent way too much money on needed things. Pen kits, pen blanks, dust collection stuff, zci for the table saw, etc. etc. Stopped by the orange borg on the way home and had one of the Ridgid Oscillating Spindle sanders in my arms carrying it to the register and then...
  12. Gofor

    Boy! Was I wrong!

    about the height of my workbench. I built a work bench last year and after much perusal on the Internet, etc, decided to go with the recommendation of "the height of your wrist when hanging loosely at your side" (for me that came to 32") As some may know, I am on the quest to become...
  13. Tom Dunn

    Correct me if I'm wrong, please.

    At the picnic there was a gentleman(Woodart perhaps?) that had a back slat with him for a rocker. Beautifull wood! As I recall, it was sycamore, but, on another site, a guy said that sycamore was pretty much useless for furniture. Is my recolllection incorrect?
    • Tom Dunn
    • Thread
    • correct wrong
    • Replies: 12
    • Forum: Wood
  14. ebarr

    Anyone notice the TWA dates are wrong?

    The TWA announcement at the top of the page states the TWA meeting is the 17th. The meeting on their page is the 18th with the workshops on the 19th and 20th. Just an observation.
  15. Arguseyed

    Wood storage, milling, where did I go wrong?

    Last weekend I was building a simple panel cutting sled and grabbed a piece of 5" wide 4/4 scrap poplar to use as a fence. Yeah, I know poplar is not the best choice but it's what I had. I proceeded to face joint, plan to thickness, edge joint and then rip to size. Final dimensions = 31"...
  16. K

    Boy am I on a roll, the wrong kind

    If they give an award for the biggest idiot of the first quarter of 2008 I have already won it and it is just the middle of March. And now my latest screw up. I can not say for sure just how many drawers I have made with the Leigh D4 but is a bunch. Please let me say in self defense it has...
  17. B

    Where did I go wrong?

    So after many months of sitting in the garage, I finally decided to put the finish on my cherry occasional table I made in a Woodcraft class. I sanded the table starting at a 120 grit, moving to 150, and then 220. I applied 5 coats of Danish Oil with about 30 minutes in between each coat, per...
  18. sapwood

    What's wrong with this picture?

    Harbor Freight email I received today :oops:
  19. T

    Is there something wrong with my PC router, check out pic...

    I was cutting a lot of dove tails and at the end of the job I noticed the bit looked charred and the collet appeared burnt. This is the first time that I have ran a router a lot and wanted to know if this was normal. I cut 16, 8" drawers with 1" tails. I was cooking along well and let the bit...
  20. Tarhead

    HF Moisture Meter Question: Is it broken or am I doing something wrong?

    I'm on my second one of these and this one is doing the same thing. I do not get a reading on green or dry wood, high or low scale. If I touch both tines to my skin it reads but nada in wood. Nothing about this in the instruction sheet. I've tried really pushing it in to the wood but I'm afraid...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top