fence

  1. Steel City Deluxe/Industrial Tablesaw Fence

    Steel City Deluxe/Industrial Tablesaw Fence

    Steel City Deluxe/Industrial Tablesaw Fence
    • ehpoole
    • Media item
    • city fence steel tablesaw
    • Comments: 0
    • Album: Threads
  2. S

    Aftermarket fence recommendations?

    Has anybody with a R4511 Rigid table saw (the one with the granite top) "upgrade" the fence on it? I like the original fence, but made a big mistake. I refaced it with phenolic ply, and used industrial strength two sided tape to hold the ply to the fence's face applying (too much) pressure...
  3. N

    My fence is twisted...

    I know that this is not new news in regards to the Ridgid fence, but should I worry about this?... I'm not talking about 90 deg to the blade/miter slots, I'm talking about vertical fence-to-table. It's square at the front along the length of the table and the back remains .25 of a deg. off...
  4. Touchwood

    Fence Stop/ Wood Magazine November 2010

    Hi All, Maybe some will remember the visit to Raleigh by Marlen Kemmet last year. Marlin is the Managing Editor for Wood Magazine and had happened upon our NCWW site, was totally impressed, contacted Doug Robinson, and asked for an opportunity to check us out...Doug then collected Scott Smith...
  5. Don_Patterson_Shop_004

    Don_Patterson_Shop_004

    • Touchwood
    • Media item
    • fence magazine stop wood
    • Comments: 0
    • Album: Shop Stuff
  6. Don_Patterson_Shop_003

    Don_Patterson_Shop_003

    • Touchwood
    • Media item
    • fence magazine stop wood
    • Comments: 0
    • Album: Shop Stuff
  7. Don_Patterson_Shop_002

    Don_Patterson_Shop_002

    • Touchwood
    • Media item
    • fence magazine stop wood
    • Comments: 0
    • Album: Shop Stuff
  8. Don_Patterson_Shop_001

    Don_Patterson_Shop_001

    • Touchwood
    • Media item
    • fence magazine stop wood
    • Comments: 0
    • Album: Shop Stuff
  9. SteveColes

    Laguna Drift Master Fence

    While not mentioned on the website,Laguna will sell the Drift Master Fence for $295 down from $395. Call 800.234.1976 and ask for Frank in sales. If you tell him that you saw this posted on ncwoodworker, he'll take the price down further to $285 :eusa_danc: eusa_danc. If you have any problems...
  10. P

    Resaw Fence

    Having just purchased a new band saw and after reading "Copy of Bill Clemons bandsaw fence" by eyekode, I built my own fence. I basically replicated eyekode's rails and table extension. Here is my table, hickory rails with a red oak table extension. Since I regularly wax my cast iron table...
  11. Bandsaw table with rails

    Bandsaw table with rails

    I made the rails out of hickory and the table top extension is red oak.
    • Padauk
    • Media item
    • bandsaw fence resaw
    • Comments: 0
    • Album: ResawFence
  12. Front of bandsaw fence

    Front of bandsaw fence

    Notice the small board in the center. By sliding this guy up and down, I can resaw any height up to 12".
    • Padauk
    • Media item
    • bandsaw fence resaw
    • Comments: 0
    • Album: ResawFence
  13. Back of bandsaw resaw fence (right side)

    Back of bandsaw resaw fence (right side)

    After sliding bed to appropriate depth, this knob locks the right side of the sled.
    • Padauk
    • Media item
    • bandsaw fence resaw
    • Comments: 0
    • Album: ResawFence
  14. Back of bandsaw resaw fence (left side)

    Back of bandsaw resaw fence (left side)

    Back of fence. 2 knobs on right side (vertical) permit sliding fence to desired thickness. 2 knobs on right (horizontal) used to adjust blade drift. 2 knobs in middle raise and lower section under blade guides to height of board being cut. Note: The drift knobs are now painted red to remind...
    • Padauk
    • Media item
    • bandsaw fence resaw
    • Comments: 0
    • Album: ResawFence
  15. TN Woodie

    Delta Saw with Incra Fence

    http://knoxville.craigslist.org/tls/1930262324.html Apparently not a unisaw, but cabinet with router lift and incra fence. Seems pretty good to me for $800.
  16. Cato

    New fence for table saw

    I ordered a Delta T2 fence to replace the OEM fence that came with my R4511 table saw. The original fence has gotten me by, but it has never been totally satisfactory because of the split rail design that tends to flex whenever the fence is locked down across the split rails. Just a bad design...
  17. M

    Win a FREE Micro Fence System!

    Hi folks, Thank you all for your support and for participating in this FREE DRAWING. If you haven't entered yet, you may do so at www.microfence.com Good Luck! If you have any questions about our product, let us know. Rich
  18. eyekode

    Copy of Bill Clemmons bandsaw fence

    Thanks Bill for the ideas behind your bandsaw fence. I promised I would post some pictures when I finished mine and here they are: View image in gallery I did a very similar design for the actual fence. However I did not copy your pivot mechanism. View image in gallery And honestly I...
  19. merrill77

    Kreg bandsaw fence - how do you like it?

    I'm considering it to help with resawing...
  20. kooshball

    Anyone have extended rails on their G1023Z fence?

    I have a stock G1023Z (with fence that guides on angle irons) with a 25" rip capacity but am going to need to go wider. Grizzly sells an extended rails that go out to 50" but they have legs for support and I am not going to be able to accommodate that due to my less than planar floor and need...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top