fence

  1. New sleeve for rip fence base

    New sleeve for rip fence base

    New sleeve for rip fence base
    • MarkE
    • Media item
    • Comments: 0
    • Album: Grizzly G0623X Assembly
  2. Rhythm House Drums

    Adjusting sawstop fence

    Sawstop fence issue Ok, I took a video of my issue. My dial is snug in there so that's not the issue. Also the fence is not moving. My shed isn't insulated yet and can get pretty hot/humid. Could the MDF have swelled at the end. Any suggestions?
  3. Resaw fence based on Kreg bandsaw fence

    Resaw fence based on Kreg bandsaw fence

    • merrill77
    • Media item
    • Comments: 0
    • Category: Member Galleries
  4. Miter saw fence

    Miter saw fence

    Miter saw fence
    • MarkE
    • Media item
    • Comments: 0
    • Album: New Shop
  5. Miter saw fence

    Miter saw fence

    Miter saw fence
    • MarkE
    • Media item
    • Comments: 0
    • Album: New Shop
  6. R

    First Post/Fence for Miter Saw Station

    Hi everybody, this is my first post so let me know if I'm doing anything wrong... Anyway, I recently started to build on my interest in woodworking so I've decided to set up my shop in the basement. I wanted to put a miter saw station on the longest wall and have the saw on top of a recessed...
  7. DanR

    First project at the new house: Cedar picket fence

    Hi Folks, My first project will be a picket fence (about 450 feet of fence, about 5 feet tall). I think I saw a suggestion on here to buy rough wood and plane it myself to save money. I found a good price on the DW734 and before I buy it wanted to double check to see if that is a good idea...
  8. kooshball

    Good time to upgrade the whole TS fence vs just getting long rails?

    I have the G1023Z saw with the 25" rail Shop Fox Fence listed below: http://www.grizzly.com/outlet/Fence-w-Standard-Rails/G4722 I currently don't have issues with parallelism but just don't have enough rip capacity and have ordered the 49" rip length rails. Unfortunately, the rails arrived...
  9. SteveColes

    Replacement for pm2000 Accu fence.

    I've had this saw since the fall of 2006. And in general I love it. BUT, I have always had a problem aligning the Rip Fence and getting good clean rips. I always assumed that I was at fault. Some how I was doing a bad job of alignment and the dirty rip cuts were bad technique. Now all of that...
  10. Jim M.

    Wilm Craigslist -Delta unisaw w/Biesemeyer fence

    Not mine, but looks in great shape. Jim http://wilmington.craigslist.org/tls/2331621328.html table saw - $750 (Wilmington, NC)Date: 2011-04-18, 12:46AM EDT Reply to: sale-gfmhm-2331621328@craigslist.org [Errors when replying to ads?] Left tilting Delta unisaw w/Biesemeyer fence...
  11. MarkE

    Incra Jig (fence) and router table

    Not mine. Looks like a great deal. http://raleigh.craigslist.org/tls/2309859104.html Date: 2011-04-06, 8:21PM EDT Reply to: see below Downsizing my Shop – great prices. For SALE: INCRA JIG and Router Table with Castors (never used) and instruction booklets for Jig - $125.00 Router...
  12. G

    Straight rip fence

    On my Delta saw I used the miter gauge that came with the saw and placed a speed square on it to check to see if the rip fence was straight and it wasn't. It appears that the back end was about 1/16 to 1/8 further left than the front end when the fence is locked down. I tried to adjust the...
  13. S

    Delta unisaw fence and rails - $175 (durham)

    not mine http://raleigh.craigslist.org/tls/2291727929.html DELTA UNISAW FENCE AND RAILS - $175 (DURHAM) Date: 2011-03-28, 3:34PM EDT Reply to: sale-qy7wt-2291727929@craigslist.org [Errors when replying to ads?] I have Fence and Rails that will fit a Delta or Rockwell Delta Unisaw. These...
  14. D

    Excaliber track and fence system

    I am looking at an older (87) model UNISAW and it has an Excaliber fence and track system. Does anyone have any input (pros and cons) on the Excaliber system? Thanks, Tim
  15. S

    52" Biesemeyer T-Square Table Saw Fence System - $125 (Holly Springs)

    Not mine http://raleigh.craigslist.org/tls/2222968195.html 52" Biesemeyer T-Square Table Saw Fence System - $125 (Holly Springs) Date: 2011-02-19, 11:06AM EST Reply to: sale-wq7ae-2222968195@craigslist.org [Errors when replying to ads?] 52" Biesemeyer T-Square Table Saw Fence System...
  16. S

    Magswitch Universal Fence Base -Rockler $90

    http://www.rockler.com/product.cfm?page=21370 Free shipping no tax with this order! Til Jan 29th I ordered mine this morning! :tool: err.. jig! M
  17. kooshball

    Should the jointer fence touch the outfeed table?

    I am tring to set the fence on my grizzly g0490 8" jointer but I am not sure if it should be supported by the outfeed table or if it should be suspended just above so that it can adjust freely. Any thoughts?
  18. S

    Mule Accusquare Rip Fence M-1040 - $125 (N. Raleigh)

    Not Mine http://raleigh.craigslist.org/tls/2168328397.html Mule Accusquare Rip Fence M-1040 - $125 (N. Raleigh) Date: 2011-01-19, 8:44AM EST Reply to: sale-9w88f-2168328397@craigslist.org [Errors when replying to ads?] Mule Accusquare table saw Rip Fence M-1040 Increased rip capacity...
  19. S

    DeWalt Table Saw Fence Rail - $100 (High Point)

    Might be good deal for someone, not Mine http://greensboro.craigslist.org/tls/2150040188.html Table Saw Fence Rail - $100 (High Point) Date: 2011-01-08, 11:45AM EST Reply to: sale-6wujc-2150040188@craigslist.org [Errors when replying to ads?] DeWalt 52" Precision Fence Rail Model...
  20. Steel City Deluxe/Industrial Tablesaw Fence

    Steel City Deluxe/Industrial Tablesaw Fence

    Steel City Deluxe/Industrial Tablesaw Fence
    • ehpoole
    • Media item
    • Comments: 0
    • Album: Threads

Our Sponsors

LATEST FOR SALE LISTINGS

Top