custom

  1. custom violin

    custom violin

    Semi hollow electric violin, 2 piece quilt maple on reclaimed pine hollow frame,, purple trantint dyed,, nitro lacquer. Finish
    • mahogany
    • Media item
    • custom violin
    • Comments: 0
    • Category: Member Galleries
  2. custom violin

    custom violin

    Custom violin
    • mahogany
    • Media item
    • custom violin
    • Comments: 0
    • Category: Member Galleries
  3. Stuart Kent

    Hot Off The Press!!!

    I'm shouting from the mountain top again (although it's really more like almost sea level here and the trees are way higher than my house). My third and latest ad just came out in Our State Magazine! Help support professional woodworking in NC - and spread the word about my custom furniture...
    • Stuart Kent
    • Thread
    • advertisement classes custom end furniture kent magazine ourstate stuart tables
    • Replies: 9
    • Forum: User Announcements
  4. Custom Knife Block

    Custom Knife Block

    This Custom Knife Block is 17" wide by 14" deep by 14 " tall and weighs 45lbs. Holds 59 knives, 3 steels and a pair of shears. Made from Cherry,Tiger Maple with Ebony accents
    • wdkits1
    • Media item
    • "the beast" block custom knife
    • Comments: 0
    • Category: 2013 Contest Winning Entries
  5. wdkits1

    Virge???

    Hi Everyone I was commissioned to do 8 of these. They are made from Peruvian walnut( laminated 5 Ply for strength ) and scrolled, then attached to a 37” tapered Mahogany shaft with a brass tip. I used my bandsaw jig to taper the shafts then turned the round knob and attached together with a...
  6. woodworker2000

    Request for Quote for Laundry Room Cabinets - Anyone Interested?

    I am considering having some cabinets made for our laundry room. I have thought about making them myself but my wife will probably insist that I get them finished before the next election. With my schedule, that may not be possible. Here is what I am looking for: (1) 24" wide sink base w/2...
  7. D

    Need custom router bit.

    Have a restoration project on a Brownstone in Brooklyn and I need to replace some molding. Does anyone know of someone who can tool routerbits to match a specific profile? Thanks
  8. Walnut Djembe

    Walnut Djembe

    Djembe Drum - walnut and yellow heart
    • Rhythm House Drums
    • Media item
    • - custom djembe drum drums hand
    • Comments: 0
    • Category: Member Galleries
  9. S

    Custom Bass Guitar Build

    Just want to show you all my first bass guitar I built. I've built other guitars but never a bass. This one was incredibly challenging because the body has a radius to it. Nothing was flat so jigs and templates were very difficult. Please let me know what you think. I'm looking to start doing...
  10. S

    Hovarter Single Handle Custom Face Vise

    I've replaced the twin screw face vise on my Holtzapffel Bench with a Hovarter Single Handle Custom Face Vise from www.HovarterCustomVise.com. I wrote a quick review and posted two 20+ minute assembly/review video's on YouTube. Check you my blog if you're interested in a killer vise...
  11. CatButler

    Custom Branding iron on a BIC lighter

    Interesting idea. Some guys around here made their own model a few years ago that was either tapped to a screw or inserted on a soldering iron. They made one batch and then it seemed to fall apart. Not sure what happened to them...
  12. wdkits1

    Custom Knife Blocks--Part 4--Lots of Slots

    The fronts of each block consists of 5 pieces of 3/4”stock cut to precisely the same size and all cut at a 9 degree angle on each end. Each of these sections have different slots for different size blades so a set of templates were made to use for consistency and to speed up the process...
  13. wdkits1

    Custom Knife Blocks--Part 3--Inlays

    Each of the knife blocks gets a quarter circle bloodwood inlay on each side where the ends of the side pieces come together. On the prototype I made a jig to use a 2” forstner bit to cut an 1/8” deep recess for the inlay but the client wanted the inlay bigger so I bought a 3” forstner bit...
  14. wdkits1

    Custom Knife Blocks-Part 2-- glue ups

    One of the biggest challenges of making 25 of anything is being consistent with all of the measurements and finding ways to do glue-ups efficiently. The sides of the blocks all have to be the same size on the top dimension so when the fronts are attached everything matches up. I found out...
  15. wdkits1

    Custom Knife Blocks

    Hi everyone As some of you may know I got a sizable commission for producing some custom knife blocks for a client that will give them as Christmas gifts to their best customers. When I had originally talked with the client they had wanted to order as many as 40 of these blocks but after...
  16. Splinter

    Custom Furniture Needed

    I was contacted by an aquaintance about a lady that is looking for someone to make some furniture for her. I don't know what she wants make. If someone here is interested in making custom furniture send me a PM and I will give you her name and # to call for the deatils.
  17. wdkits1

    Another Custom Knife Block

    Hi Everyone Had a new client call me last week inquiring about my custom knife block that was seen on CustomMade.com and wanted to know if I was interested in designing one for him. Sure!!! He sent me the scaled template of what he wanted to include and chose Walnut and Cherry for the...
  18. Truefire

    What are your perspectives on custom projects?

    What in your mind and or perspective constitutes custom made woodworking? Is it the integration of select elements of an artist or woodworker into his/her work that display their personality and individual style in the work created? Or is it the creation created from a vast array of customer...
  19. steviegwood

    ?? About selling custom photo frames

    Hi Folks, Do any of you make and sell any custom picture frames? If so what is a decent asking price? The reason that I am asking is that I have had a number of people wanting me to make and sell the Treebark Rustic Frames that I make for all of my portrait work. I have never just made and sold...
  20. zapdafish

    Made a custom tool rest

    Thanks to Matt (aka Splint Eastwood) and his metalworking I was able to make a custom tool rest for my mini lathe. The mini is small enough already, I was kinda peeved to lose so much from the diameter of the workpiece because of the tool rest base. This one is a prototype made out of mdf and it...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top