hole

  1. use a backsaw to cut the sides

    use a backsaw to cut the sides

    • eyekode
    • Media item
    • dog hole square strip
    • Comments: 0
    • Category: Shop Photos
  2. mark/outline all edges

    mark/outline all edges

    • eyekode
    • Media item
    • dog hole square strip
    • Comments: 0
    • Category: Shop Photos
  3. Flute Maker

    Chuck With 1" Pass Through Hole

    I need a chuck with a 1" pass through hole that isnt terribly expensive for a custom gundrill tailstock
  4. Canuck

    Kreg K3 Pocket Hole Jig - Raleigh CL

    This is a pretty good deal for the Kreg K3 kit. This one has the clamp handle in the front. Not mine, but looks like a pretty good deal, none the less! Wayne http://raleigh.craigslist.org/tls/2280313301.html Kreg K3 Jig Master System Pocket Hole Jig - $75 (Creedmoor) Date: 2011-03-22...
  5. S

    Pocket hole machine

    I was looking around for a pocket hole machine (my arm is tired!) the Kreg Foreman is nice but way to expensive for my use. I came across this video http://www.youtube.com/watch?v=6gjqqzvVXFc and this guy has got a great shop built machine. Check it out! and be sure to give him a Thumbs Up...
  6. sbarnhardt

    Hole Saw Recomendation?

    I'm wanting to buy, or start to assemble, a good set of hole saws. In a prior life/job I worked for a distributor that rep'd the Lenox line. Good products, but that's been a lot of years ago. The end result being, I don't have a clue now which are good and which are not so good. In other words...
  7. D

    Sommerfeld Pocket Hole kit at Peachtree 50% off

    http://www.ptreeusa.com/edirect_011411.htm
  8. NCTurner

    How would you, stepped hole?

    I am making a DP table from some 1-1/2" melamine, and want to make a removeable offset insert, but want to use some 1/2" MDF I have. How would you do the cut out?
  9. JackLeg

    Where's the Hole?

    Fellow came by this morning to pick up a set of Corn Hole boards I had built for him. I went out to the shop with him to load them up. I carried one over to his truck and had started over with the second one when he said, "Ain't there supposed to be a hole in these things?" :embaresse...
  10. NCTurner

    Help Need an Auger or post hole digger

    Does anyone in the Raleigh/Cary area have an Auger or a post hole digger I can borrow? I need to do 4 holes.
  11. Bas

    Pocket hole screws & joint creep

    I'm trying to make a simple butt joint between two pieces of plywood. They're about 10" wide. I drilled two pocket holes (at the correct depth for 3/4"), put one piece on the other, and clamped them together with a Kreg right angle clamp. The edges are perfectly flush at this point. The problem...
  12. Canuck

    Powder Post Beatle Hole ?

    Is there anyone out there that has any experience in filling those wee powder post beetle holes in wood? They are only about the size of a pin-head, but if there are a lot, that is a little too much "character" for me. I have tried wood fillers in the past, but all I end up with are white...
  13. Mr. Lahey

    How can I make a deep, ellipse shaped hole with handtools?

    I'm working on a project which requires me to make a hole about three inches deep which is shaped like an ellipse. Is there a way to do this with hand tools and a drill? Oh by the way its not a hole that goes all the way through, so its really more of a deep mortise I guess.
  14. Bas

    Kreg pocket hole screws & clamps

    I plan to build my cabinets using pocket hole screws (if I can ever get my thumb out of this splint... :BangHead: :BangHead: :BangHead:). The screw length charts, like the one at McFeely's are very helpful, but don't address screw gauge. A few questions: What screw gauge do you use for...
  15. Bas

    Pocket hole jig

    I came across this item. It's made of aluminum, not plastic, $70, step drill bit included. Anyone have this particular item? The dual guide system looks intriguing, that's something I hadn't seen before. It's rather heavy at 4 1/2lbs, but obviously meant to be mounted to a workbench. I have a...
  16. CarvedTones

    A "boring" post about a hole in one

    A hole in one blank, that is. I bored a 3/8" hole through a blank over 1' long. I came in from both ends and there is no perceptible lip where the holes meet! But it seems like I am using too many steps, so I thought I would post and get some feedback. I got a hollow center with a removable...
  17. sawduster

    Square peg - round hole

    when inserting one (square) blank into one ( round ) barracuda chuck should the corners go between the jaws or centered in each jaw ? :help: ......did that make sense ? :icon_scra TIA for any and all input :icon_thum
  18. wdkits1

    Home made pocket hole plugs

    Hi everyone l love using pocket hole screws. They are quick, easy to use and make a strong connection. The down side is that you normally can't use them for exposed work mostly because they are kind of ugly. Well on the latest project that I'm working on (custom closets) there are a few...
  19. Mark Stewart

    help patching a hole in green turning

    I have had one of those days in my little space of turning. I have a green turning almost finished then got stupid and now I have a small hole in the side of this nice piece o cherry. Can some one give me suggestions for patcing? Some say saw dust and white gler mixed any others? Thanks Mark
  20. flatheadfisher

    Slotted Hole?

    I am trying to figure out how to build the new doors for the kitchen cabinets. With my very limited skills, and my wife wanting her kitchen back in order, I want to use a method that will result in nice looking doors without spending hours learning a new technique. So, I have made the panels -...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top