inside

  1. AmishWarlord

    Box construction materials

    When building an item like a gun case is it accessible to use materials like MDF or plywood for the inset that will be covered by velvet or for quality should this also be made of hard wood? On one hand I can see that it's glued in, cover over, never to be seen. On the other hand if you...
  2. instruments inside the hazen

    instruments inside the hazen

    • carolina new be
    • Media item
    • hazen inside of the view
    • Comments: 0
    • Category: Member Galleries
  3. Joe Scharle

    Inside Greg Paolini's Workshop

    http://www.finewoodworking.com/item/37349/shop-tour-furniture-maker-greg-paolini?utm_source=email&utm_medium=eletter&utm_content=20110521-free-plan-library-table&utm_campaign=fine-woodworking
  4. M

    Need help lining the inside of a box

    I would like to make a wooden box that holds a couple of drinking glasses. I can make the box, but the inside is where I need help. Anyone have any experience lining the insides of a box that would hold my glasses securely, probably in padding, or something to protect the glasses? I also have...
  5. zapdafish

    what do you use to sand the inside of a bowl?

    Not quite sure what the best way is to sand out the interior of a bowl and would like to see what you guys are using. I tried by hand with sandpaper but it heats up kinda quick and if I am not careful I end up with a groove from the edge of the paper which means more sanding I saw some mention...
  6. Spalted Pecan Inside Bowl

    Spalted Pecan Inside Bowl

    • Nate Davey
    • Media item
    • inside pecan spalted
    • Comments: 0
    • Category: Member Galleries
  7. H

    Chatter with bowl gouge? Inside roughing cut

    All: A relatively novice turner here - at least as far as bowls go. I likely have more "spare" pen parts than most of you, as least as a ratio with the number of pens I have completed (5?). I am trying my hand at some maple bowls with a natural edge. One piece is about 10" in diameter and...
    • Henry W
    • Thread
    • bowl chatter cut gouge inside roughing
    • Replies: 20
    • Forum: Woodturning
  8. CrealBilly

    Question - Routing inside corners

    Routing inside corners with a round-over bit creates a radius at the corner. I have been whipping out the chisel and sand paper to make it square - is there a better way? a picture is worth 1000 words Thanks
  9. J

    First Time- It's pink on the Inside

    Today, for the first time I used some of the disappearing color ceiling paint. Opened the can, and it was PINK! Applied it to existing ceiling, and as it dried, it turned back to ceiling white. Makes it easy to see where you have and haven't done, plus what areas need more. Costs about twice...
  10. S

    How to center on remount for inside of bowl

    Hi all, I am still fighting back but need some specific advice. I have a PSI chuck and just bought a Oneway Termite hollower and am doing better but here is a situation I do not understand. I was going to send a picture but I am sure you have all seen this. I am turning from a slice of a...
    • sasjzl
    • Thread
    • bowl center inside remount trials turning
    • Replies: 17
    • Forum: Woodturning
  11. Bas

    When is lumber dry enough to move inside?

    Google resulted in 39,300 hits, so let me just ask the experts here: I've been air drying some 4/4 walnut for the last 6 months. Moisture content is down to 15%-17% (thanks Wayne for lending me the moisture meter...). Is that dry enough to bring inside :dontknow:, or should I wait until it...
    • Bas
    • Thread
    • dry inside lumber move
    • Replies: 7
    • Forum: Wood
  12. MikeH

    Drawer inside bathroom vanity...

    LOML and I were talking last night and she would like additional storage inside her bathroom vanity. Something that slides out would be ideal. Do you have something like this in your bathroom? If so, how did you do it?
  13. cskipper

    Staining inside cuts different colors

    If I wanted to add a little color to the inside cut edges different than the top - would it work to put a carefully applied coat of poly on the top and then do the color on the inside cuts? Would the top coat of poly prevent any "spill over" (translate as sloppy, unskilled) of the color from...
  14. DaveO

    Finishing the inside of boxes

    I am working on a small cedar chest 14" x 8" x 9" and really like the cedar smell to the inside of the box. I will probably finish the outside of the box with Waterlox S/F, but I am torn as to what to do with the inside. Obviously if I put any finish in there it will be shellac, but I rather do...
    • DaveO
    • Thread
    • boxes finishing inside
    • Replies: 10
    • Forum: Finishing

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top