bearing

  1. Truefire

    Jet Midi lathe 1014 bearings replacement walk through (picture heavy)

    My poor little girl, the Jet Midi lathe VS1014 was in need of some bearing replacements. It should be a very straightforward process, you know the whole 'knock out a bearing and just replace it' kind of thing. I just thought I would share the repair in the event someone might be concerned...
    • Truefire
    • Thread
    • bearing jet lathe midi replacement
    • Replies: 17
    • Forum: Woodturning
  2. J

    I Went With a CHEAPER Bearing

    Last night, I took my Delta OSS apart to replace a bearing. I went to FastenAl's web site and looked at their selection of 6002 bearings. One bearing stood out from the rest. Their SKU# 4126048, priced at THREE THOUSAND, THREE HUNDRED, TWENTY-SEVEN DOLLARS, and FORTY EIGHT CENTS ($3,327.48) To...
  3. cyclopentadiene

    How do I tune bandsaw bearing guides

    I just upgraded to a Jet 18" band saw with bearing guides. My former saw had conventional guides with cool blocks and i generally set the guides to a sheet of paper distance from the blade. How do I adjust the Jet guides to best tune the saw. i.e. should the blade actually be embedded in the...
  4. J

    Cheap Bearing Heater

    Today, I was changing out some bearings on an electric motor. Used puller to remove old ones. Took the new ones, one at a time and set it on top of a 60 watt light bulb (lit of course) for about three minutes. Wearing a leather glove picked up bearing an dropped it onto the shaft.
  5. MrAudio815

    Is this Bearing still in good shape?

    Merry Christmas NCWW's, I pulled this bearin off the straight blade cutter head on my jointer and wanted to know if it still looks good enough to use on the Shelix cutterhead? Don't wan't to get it on and it not be good. Chipped black stuff right side middle Closer view of other side...
  6. ScottM

    lathe bearing

    I think I have a bad bearing on my mini lathe. Dissembling was fairly easy even for me.:embaresse Any way the bearing is a 6005-RZ. When I looked on-line I see RS and ZZ bearings but no RZ. I have checked it several times and it clearly is RZ. Will RS or ZZ work in it's place and is there a...
  7. CrealBilly

    Ball Bearing Drawers Slides Are Really Sucking

    I'm about ready to take a 3lb hammer to two pairs of BORG bought heavy duty ball bearing drawer slides. The cabinet is square, the drawers are square. With the drawers closed one end of the drawer sticks out about a 1/8" of an inch from the cabinet on the RIGHT hand side. The other drawer...
  8. S

    Delta bandsaw lower thrust bearing stop

    Hi, I have a standard Delta 14" bandsaw that I have been ignoring and am starting to use again to cut blanks for wood turning. My problem is that on the lower guide assembly the mechanical setup that keeps the thrust bearing in place to keep the blade from being pushed back is not holding...
  9. froglips

    A pressing gloat that has some bearing.....

    Ok, I'm sipping my victory beer :occasion1 Copious pics will follow tomorrow, as I'm done for the night. As a teaser..... I have totally disassembled and pulled the shot bearings out of an old Craftsman 1/2 sheet sander. Then, with the help of some folks on the board, I got the new...
  10. steviegwood

    Setting Bearing Guides on Bandsaw

    Hi Y'all, I have set the bearing guides on my new band saw the way the book says to set them but I do not understand why they set them this way. If the bearing guide is to be set to where the bearings do not touch the blade how do they guide the blade without some drift? Can someone help explain...
  11. S

    MT2 ball bearing center from Harbor Freight

    Hey I was wondering about the MT2 ball bearing center from Harbor Freight. Has anybody ever used one of these and if so does it work well? Could it work on my shopsmith with a #2 MT? It seems to look pretty good but any feedback would be really helpful. Thanks, Patrick
  12. K

    Jointer bearing question

    In another post SCSMITH42 (Scott) suggested I check the bearings in my jointer, 6" Delta Professional. OK, how do I do this?:dontknow:
  13. alleng

    Bandsaw bearing grease

    Was just wondering if anyone had any idea about how to grease the bearings on a bandsaw with this type of grease fitting. And also, what type of grease is recommended??:eusa_thin
  14. froglips

    This post has no bearing on....

    Well, I picked up an old 6" planer/molder from CL this week. Its one solid block of iron! Its an Eastman Foundry machine. I found zilch on this company, not even OWWM had anything. I kind of "horked" one of the bearings that hold the cutter head. Its beyond repair. Anyone happen to...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top