lathe
-
Reeves drive type lathe speeds
Just wanted to share a small tip to those that may have a Reeves-type lathe or Shopsmith. I purchased a used Shop Fox lathe and the minimum lathe speed that it would go down to was 690 RPM's. Watched a few videos on maintenance on these lathes and decided to try it myself. First I bought a...- Sam Knight
- Thread
- lathe reeves drive shop fox
- Replies: 1
- Forum: "How To" Forum
-
Air Filter
- Pop Golden
- Media item
- chuck lathe
- Comments: 0
- Category: Member Galleries
-
My first attempt at turning a bowl and a mushroom
Here is my first ever bowl. It was made from ash that was cut into a bowl blank back in march. My wife likes the natural edge bowls so that is what I attempted. It is in a bag with shaving now, hopefully it will not warp much but we will see. I need to get a small weigh scale to weigh as the...- Sam Knight
- Thread
- bowls lathe mushrooms turnings
- Replies: 14
- Forum: Woodturning
-
Free Turning Videos (for now)
I've been enjoying the "Woodturning with Tim Yoder" videos. Popular Woodworking Magazine made all 24 Season 1 videos free to stream as they promote Season 2. Tim works with both traditional and carbide tools and has a fun personality, so when you aren't learning something, you can simply...- CommGuy107
- Thread
- instruction lathe turning video woodturning yoder
- Replies: 2
- Forum: Woodturning
-
A Couple of Great Books
Just picked up a couple of new (well...new to ME) books this week. The first, "Bandsaw Handbook" by Mark Duginske is crammed full of useful information on setup, techniques, safety, and even projects for any bandsaw owner. I could easily recommend it to any woodworker - not just for the...- CommGuy107
- Thread
- bandsaw books lathe turning
- Replies: 5
- Forum: General Woodworking
-
Atlas Lathe
- thrt15nc
- Media item
- atlas lathe
- Comments: 0
- Category: Member Galleries
-
Atlas Lathe
- thrt15nc
- Media item
- atlas lathe
- Comments: 0
- Category: Member Galleries
-
Atlas Lathe
- thrt15nc
- Media item
- atlas lathe
- Comments: 0
- Category: Member Galleries
-
Atlas Lathe
- thrt15nc
- Media item
- atlas lathe
- Comments: 0
- Category: Member Galleries
-
Atlas Lathe
- thrt15nc
- Media item
- atlas lathe
- Comments: 0
- Category: Member Galleries
-
C
Sometimes the tool is the project
I'd been planning to order grizzly's new 22" lathe, but checked craigslist one last time before calling to order. And lo and behold, there was a 1960s Oliver No 20a Patternmakers lathe. I'd missed one a month or two ago for around $1200 and had been somewhat regretting it. Since there was no...- Chemeleon
- Thread
- lathe old iron oliver restoration
- Replies: 46
- Forum: Woodturning
-
Carbide tool handles
I decided to make a set of carbide lathe tools. I turned the handles today. While they are only 16 inches long this is the longest I can turn on my little Rikon lathe. I'm very happy with the way they turned out.- hymie123
- Thread
- carbide handle lathe
- Replies: 16
- Forum: Woodturning
-
Lathe handles
- hymie123
- Media item
- handle lathe turning
- Comments: 0
- Album: Projects
-
Lathe handles
- hymie123
- Media item
- handle lathe turning
- Comments: 0
- Album: Projects
-
Handicap Lathe Stand
Sketchup and JPG of the Outreach Adjustable Handicap Lathe Stand Design. Original Design by Phil Soper. Sketchup Drawing by Bill Clemmons.- KenOfCary
- Media item
- adjustable lathe stand
- Comments: 0
- Category: Outreach Trailer interior
-
Lathe spindle morse taper at headstock...How to clean superficial rust inside the taper?
This conversation actually took place before just a few days ago underneath another topic but it was really never fully completed. So I decided to receive some further clarification and began another topic with this title so others could find via a search at a later date. I have some...- Truefire
- Thread
- #2 morse taper lathe reaming spindle shaft reaming taper cleaning
- Replies: 18
- Forum: Power Tools and Their Use
-
Jet Midi lathe 1014 bearings replacement walk through (picture heavy)
My poor little girl, the Jet Midi lathe VS1014 was in need of some bearing replacements. It should be a very straightforward process, you know the whole 'knock out a bearing and just replace it' kind of thing. I just thought I would share the repair in the event someone might be concerned...- Truefire
- Thread
- bearing jet lathe midi replacement
- Replies: 17
- Forum: Woodturning
-
Carbide Lathe Tools
Maple handle, steel rod.- Rick M
- Media item
- carbide lathe tool
- Comments: 0
- Album: Shop Made Tools
-
Carbide Lathe Tools
Maple handle, steel rod.- Rick M
- Media item
- carbide lathe tool
- Comments: 0
- Album: Shop Made Tools
-
Lathe Tool Holder
Keeps the tools I\'m using from rolling around. Friction fit into the bed ways.- Rick M
- Media item
- jig lathe
- Comments: 0
- Album: Shop Made Tools