lathe
-
Lathe Tool Holder
Keeps the tools I\'m using from rolling around. Friction fit into the bed ways.- Rick M
- Media item
- jig lathe
- Comments: 0
- Album: Shop Made Tools
-
Need a material suggestion...
Little project I'm working on will have a pendulum attached to an axle, the axle will go through either a bearing or bushing (haven't decided yet) and I need to choose a material for that axle. It will be about 1/4 - 3/8 diameter, about 1 - 1.5" long, must be solid, rigid, chip resistant, light...- Rick M
- Thread
- axle lathe turning
- Replies: 10
- Forum: Woodturning
-
Well durnnit, I broke my lathe.
Bumped the motor impeller fan while it was running and snapped it right off. Wouldn't be so bad except the fan is integral to the speed control so now it runs full tilt. I can repair it but in the meantime I'll hook up a more powerful motor which I haven't tested yet. Hopefully it works.- Rick M
- Thread
- lathe
- Replies: 10
- Forum: Power Tools and Their Use
-
Tool rest 3 with wooden nut
Finished Spring Pole Lathe ala Roy Underhill- oldetoolworkshop
- Media item
- lathe pole spring
- Comments: 0
- Category: Member Galleries
-
Tool rest 2
Finished Spring Pole Lathe ala Roy Underhill- oldetoolworkshop
- Media item
- lathe pole spring
- Comments: 0
- Category: Member Galleries
-
Tool rest 1
Finished Spring Pole Lathe ala Roy Underhill- oldetoolworkshop
- Media item
- lathe pole spring
- Comments: 0
- Category: Member Galleries
-
Tailstock
Finished Spring Pole Lathe ala Roy Underhill- oldetoolworkshop
- Media item
- lathe pole spring
- Comments: 0
- Category: Member Galleries
-
Working Lathe
Finished Spring Pole Lathe ala Roy Underhill- oldetoolworkshop
- Media item
- lathe pole spring
- Comments: 0
- Category: Member Galleries
-
Headstock
Finished Spring Pole Lathe ala Roy Underhill- oldetoolworkshop
- Media item
- lathe pole spring
- Comments: 0
- Category: Member Galleries
-
AAW Symposium 2013 Tampa
- WoodWrangler
- Media item
- aaw lathe symposium woodturning
- Comments: 0
- Album: 2013 AAW Symposium Tampa
-
AAW Symposium 2013 Tampa
- WoodWrangler
- Media item
- aaw lathe symposium woodturning
- Comments: 0
- Album: 2013 AAW Symposium Tampa
-
AAW Symposium 2013 Tampa
- WoodWrangler
- Media item
- aaw lathe symposium woodturning
- Comments: 0
- Album: 2013 AAW Symposium Tampa
-
AAW Symposium 2013 Tampa
- WoodWrangler
- Media item
- aaw lathe symposium woodturning
- Comments: 0
- Album: 2013 AAW Symposium Tampa
-
AAW Symposium 2013 Tampa
- WoodWrangler
- Media item
- aaw lathe symposium woodturning
- Comments: 0
- Album: 2013 AAW Symposium Tampa
-
AAW Symposium 2013 Tampa
- WoodWrangler
- Media item
- aaw lathe symposium woodturning
- Comments: 0
- Album: 2013 AAW Symposium Tampa
-
AAW Symposium 2013 Tampa
- WoodWrangler
- Media item
- aaw lathe symposium woodturning
- Comments: 0
- Album: 2013 AAW Symposium Tampa
-
AAW Symposium 2013 Tampa
- WoodWrangler
- Media item
- aaw lathe symposium woodturning
- Comments: 0
- Album: 2013 AAW Symposium Tampa
-
AAW Symposium 2013 Tampa
- WoodWrangler
- Media item
- aaw lathe symposium woodturning
- Comments: 0
- Album: 2013 AAW Symposium Tampa
-
AAW Symposium 2013 Tampa
- WoodWrangler
- Media item
- aaw lathe symposium woodturning
- Comments: 0
- Album: 2013 AAW Symposium Tampa
-
AAW Symposium 2013 Tampa
- WoodWrangler
- Media item
- aaw lathe symposium woodturning
- Comments: 0
- Album: 2013 AAW Symposium Tampa
Premier Sponsor
Our Sponsors
LATEST FOR SALE LISTINGS
-
-
SOLD -- $75: Gast moa v113 Vacuum Pump Veneer, 60" bag and board- Started by peterdnight
- Replies: 1
-
GONE: Gladiator 5 cleats, 10 hangers, Paper Towel and Shelf
- Started by peterdnight
- Replies: 3
-
SOLD -- $100 Makita mac700 portable air + grex pin nailer + 2 others + 50' hose
- Started by peterdnight
- Replies: 1
-