clean

  1. J

    Working on (Finally) organizing my tools and getting the shop clean

    I've finally started working on getting my shop cleaned up and my tools organized. I've still more tools to get put up (chisels, etc.). But, it's coming along.
  2. cskipper

    How do I clean up poly from tile counter?

    Every time I walked into the kitchen today J have been smelling polyurethane. I was finishing baskets last weekend, but knew I hadn't left any open. Finally I saw a can I knocked over early this a.m. and the cap was not on tight. A lot had soaked into a towel, but a lot was still on the...
  3. Masonite, 1/4" clean cut

    Masonite, 1/4" clean cut

    Masonite, 1/4" clean cut
    • ehpoole
    • Media item
    • clean cut hardboard masonite tempered
    • Comments: 0
    • Album: Threads
  4. Bas

    Reminder: Clean up your moderated posts!

    Just a reminder...putting a post/ thread in moderation means it's in limbo, purgatory, animated suspension etc. It's invisible to the general public, but it's not gone either - it's waiting in the moderation queue. After all is said and done, a moderated post must be either unmoderated (making...
  5. tjgreen

    A clean shop is a safe shop

    I was tuning up a couple old planes tonight. Took them apart, got the worst of the surface rust off the iron with sandpaper and #0000 steel wool, then over to my grinder to reshape the edge...shooting sparks directly onto the oily steel wool I'd carelessly left on the corner of the bench, which...
  6. Truefire

    Clean out your dryer...fire hazard. please read.

    Hey Guys i just thought i would warn you guys and share with you a very interesting find here recently. That is a potential fire inside of my dryer that i wasn't even aware of. I have recently had to go inside of my dryer to test some electrical apparatus to troubleshoot my dryer's mishaps...
  7. kooshball

    best solvent to clean top of new table saw??

    I am putting together my Grizzly G1023Z and followed the instructions for the use of a citrus degreaser to clean the oil/wax from the top of the table but it isn't working. Before I go and buy a bunch of other solvents can someone recommend what they have used successfully (acetone, MEK...
  8. J

    Gotta Clean the Shop

    Gotta clean the shop, as I have company coming from Des Moines, IA:gar-Bi. For those who have been in my shop, you know this is a major undertaking. Wish me luck.
  9. Sawdust Denny

    Inexpensive Way to Clean Pitch From Saw Blades and Other Cutting Tool

    I learned this trick from a seasoned woodworker over thirty years ago and it is much less expensive than using the spray blade cleaners. This can be used for saw blades, router and shaper bits, etc. Make sure you remove the bearing from routing bits before cleaning. Combine a solution of three...
  10. scsmith42

    Should we clean up the members list?

    After reading Jim's thread about the "county search" feature, I took some time to review the members that are from my home county (Chatham). To my surprise, there are a significant number of members that have not signed on since the day that they signed up for NCWoodworker. I'm wondering what...
  11. CarvedTones

    Keeping' it clean (the air)

    Giving more thought to DC as I have been cleaning out the garage and moving things around and it is obvious I don't do a good enough job. Part of it is being prone to making a mess to start with. Here is a picture from last spring: There are a couple of things to note in the picture. One...
  12. PChristy

    NEVER USED-WOODSHOP TOTAL CLEAN AIR VENT SYSTEM - $200 (winston salem)

    Thought that someone might want this -it is not mine http://winstonsalem.craigslist.org/tls/788235694.html
  13. S

    Clean tools make all the difference.

    I was watching some woodturning videos online today and noticed how their chuck jaws just slid in and out with ease. So i thought "why doesnt mine do that:eusa_thin". I went out to the shop and after thorough investigation i discovered that the problem was there was dust in between the chuck...
  14. Bas

    Shop Elves and Clean Air Gloat

    The hypothetical air cleaner has become reality! :eusa_danc This evening, Scott, Wayne and Steve came by to help install the beast. It wasn't terribly heavy, but I'm glad there were three of us (Steve was unloading the tools..) to align it with all the hooks. Scott, Wayne - THANKS! It's so...
  15. ScottM

    Clean air gloat

    Knowing the rules,I did not gloat until I had the picture to prove it. Here is my Christmas gift to myself. Boy that sucker was heavy!!!!
  16. woodguy1975

    Cough, Cough, Cough The Shop is Clean!!!

    Well, the shop has been cleaned for the big even on Saturday. I have one table and converted my assembly table into another eating table. When I got home my wife was already down in the shop going at it. She had the machine room clean by that time. :eusa_danc :eusa_danc A few more hours...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top