pieces

  1. Truefire

    Looking meat department grade countertop material..smaller pieces

    I am looking for the meat department, food grade type countertop material. Not sure what this material is or where i could possibly find a couple of pieces for a project. I need about 14" of it and would glue up to a thickness of about 2". If anyone is familiar with where i might find some...
  2. Mike Camp

    Need two or three small pieces of veneer

    Was wondering if anyone in the Triangle area (closer to Apex the better) had two or three 4" by 4" pieces of veneer I could either have or could pay a small sum for. I'm going to cut them into approx. 3 inch circles on my scroll saw for my son's toy box so around 1/16" thickness or so would work...
  3. erasmussen

    1885 pieces of wood

    Got it off the lathe at last :icon_cheers now maybe I can get some turnings done. Its 33" tall got 1885 pieces of wood in it. The first picture might give an idea of its size, but doesn't show the colors at all the second shows the colors better but still not real good:gar-Cr Now thats its...
  4. Tarhead

    Auction with Greene & Greene, Nakashima and Wharton Pieces w/ free catalog

    I know I usually post great deals and for someone, somewhere, these may be great deals because they are one of a kind types of things. I know most, if not all of us can't afford them but take 5 minutes and flip through the lots at this upcoming auction at Sotheby's of important 20th Century...
  5. LeftyTom

    Ciphering the Length of The Pieces

    I want to build an eight-sided border around some landscaping I've done recently. The diameter of the circle for this border is 8 feet. Any formula to help me figure out how long each of the sides need to be? :dontknow:
  6. W

    Pieces that I built

    Since I am on vacation this week, I want to share with fellow North Carolina Woodworker'ers some of the pieces I have built. First one is a chest of drawers built for daughter. All the parts are made with maple. She chooses the finish. Second piece is a blanket chest based on the plan found...
  7. S

    holding down small pieces

    I have a commission that involves carving a number of small pieces from quarter sawn oak. These are pieces to be attached to a hall tree. I am having trouble holding the pieces in place while carving them. They can not be screwed in place or nailed in place. The pieces will have to be held in...
  8. JackLeg

    Cutting Dado's in Small Pieces

    OK, I'll admit it! I'm not real sharp in the "think and design" department.:dontknow: I did think I was pretty good at working from plans---BUT--! :icon_scra OzzieX was kind enough to send me the plans for making Chinese puzzles. I envisioned myself making a BUNCH of these for Christmas...
  9. Truefire

    Padauk, Bocote Turning stock (smaller pieces wanted)

    Hello gentleman i was wondering if any of you guys had some Bocote and Padauk turning stock in the arena of 1 3/8" (+-) x 1 3/8" (+-) x 6" or longer. I am desiring several pieces of each. Let me know, Thanks a great deal Chris 252-717-6699
    • Truefire
    • Thread
    • bocote padauk pieces smaller stock turning wanted
    • Replies: 4
    • Forum: Wood
  10. NCTurner

    A Few new Pieces.

    Spalted Ambrosia Maple HF 11"x3.5" This is a closed bowl in B. Walnut 6.5"x3.75"
  11. H

    New pieces for sale

    i added two more pieces from my shop for sale. Powermatic shaper w/power feed ShengShing wide belt sander both very good pieces www.hutchwood.com
  12. CarvedTones

    single pieces of bamboo flooring

    I want to find one or two single pieces of vertical grained bamboo flooring; either 2 pieces of 2" wide or one piece of 4" wide. Length 6' or more, though anything less than another 6' would be waste.
  13. NCTurner

    Finish sanding small pieces?

    I was using my 5" ROS to finish a large box last night and had the thought that a smaller box would be almost impossible to sand this way. I had read of using an inverted 1/4 sheet ROS finish sander, seems like a good idea. :dontknow: Just curious how some of you do it???
    • NCTurner
    • Thread
    • finish pieces sand sanding small
    • Replies: 10
    • Forum: Finishing
  14. bluthart

    Free Maple And Bradford Pear Pieces!!

    I have posted this before for the maple, but I now have some Bradford Pear chunks from another neighbor. I don't have any sealer (especially not enough for two whole trees) but I would love to give a bunch of this stuff away so it can be used for things other than firewood. The maple has some...
  15. Mark Gottesman

    WTB: Bits and Pieces for Delta 22-540 Planer

    Hello to all, Not sure if this should be here or in classifieds, but here goes. Hope everyone is having a good holiday. I have been cleaning up and greasing the used planer I just got. Thank you all for your input in this purchase. Looks like a good machine and I have found no major problems...
  16. WoodWrangler

    White/Red Oak Pieces for Scrolling?

    As part of another project I'm working on, I have about a dozen 36"-40" white and red oak strips about 5-6" wide about 1/4" thick (rough one side). Not sure if anyone would want them ... but I hate to just toss them. Thinking they might be good for scrolling? (Note: They are ROUGH one one...
  17. CarvedTones

    small pieces of thick steel plate

    I need a couple of small pieces of 1.25" or so thick steel plate. By small I mean really smalll - 3" x 2" and 2" x 2". They need dead flat parallel faces. EDIT - Oh yeah - Cary/Apex/Raleigh area.
  18. DaveO

    What to do with old furniture pieces???

    I am not talking antiques or anything special. Just stuff that I made a while back, before I really knew what I was doing (which I still don't, but getting better) I made new end tables to replace these And will soon be making a new bedroom suit to replace these as we just bought a new...
  19. D

    Looking for large pieces of cedar for mantles

    I am looking for large pieces of cedar that i can make mantles out of say 8ft long 4-6 in thick and 10-12 in wide if its a little smaller thats fine but not too much smaller, larger is fine any suggestions? Thanks Guys! Or maybee something else that would make some nice mantles but i...
  20. ChrisMathes

    How to cut a burl into useful pieces???

    I have a nice cherry burl that is still green. Does anyone have any advice, or know of a good resource that can help me with how to cut it up and how to protect it from drying too fast/slow????? I would greatly appreciate ANY help out there.... btw.... I crudely measured the ball with a tape...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top