3 or 4

  1. F

    3/4" pipe for pipe clamps

    Where is a good, and preferably cheap, source for pipe around raleigh?
  2. Phil S

    FREE Oak door slab 3/0 x 7/0 x 1 3/4

    I have four door slabs available for free. They are commercial doors and have been prepped for locksets and hinges. They are natural finished. These are at a North Raleigh commercial building and must be given away or loaded in my dump truck tomorrow morning. If you want one or more let me...
  3. C

    New 14" Delta 3/4 HP Bandsaw 28-276 - $100

    This post is part deal, part gloat, and part thanks. In case you missed it buried in the Delta 17-950L DP thread a few weeks ago, Lowes is also clearing out their 14" Delta Bandsaw. Clearance price is $349, but thanks to jhreed, tommyt654, and terry1166 (and their receipts) I just picked one up...
  4. NCTurner

    ? 3/4" Bowl Gouge

    So, I stopped by Klingspor today to take advantage of their 20% off sale, and picked up a Crown 3/4" Bowl gouge. I got this suker home and started looking at it and keep thinking this sucker is BIG:eek:. Question is, is it to big? Anyone use one of these monsters?
  5. ashley_phil

    3/4" Acetal Rod - Local Source in Cornelius

    I found this company on a internet search a few weeks ago. They have all sorts of plastic sheets and rods. I wanted some for bushings for the pen turning I need to start on with Christmas fast approacting. The source Alex told me about was sold out and I waited too long to get the special from...
  6. J

    3/4" Birch Ply at HD in Apex

    Today I was in HD in Apex picking up the last of a twenty sheet order of birch plywood. What is labeled as C-3 (shop grade) looks better than some A-2 that I have seen in the past. Clear on one face, and only a couple of dark spots on the other. But beware of the stuff made in China. Bruce
  7. D

    where can i find affordable ash 3/4 plywood?

    in raleigh area. i know of raleigh hardwoods on poole road, but wondering of any other distributors in area who may sell ash plywood! thanks all.:icon_thum
  8. Jon

    Cabinet grade plywood and 3/4 stock

    I live in Winston Salem and was wondering where I can get Cherry and cherry Plywood. Is there anywhere local? I dont mind driving to get it I just cant find any anywhere.
    • Jon
    • Thread
    • 3 or 4 cabinet grade plywood stock
    • Replies: 6
    • Forum: Wood
  9. ebarr

    Advice on 3" holes in 3/4 plywood

    What would be your advise on drilling 3" holes in 3/4 in plywood. Forstner bit or Hole saw. Keeping in mind that this may end up being quite a few holes. Let me explain... I am orignally from southern Indiana. Growing up we played a game called "Washers", this is very similar to Horseshoes...
  10. S

    Wiring: 3/4 EMT capacity

    I am a bit confused by conductor derating within conduit. A snipit of the table is: 4-6 current-carrying wires, derate 80% 7-9 current-carrying wires, derate 70% 10-20 current-carrying wires, derate 50% These numbers are irrelevent to the size of the conduit. 10 wires derate at 50% in...
  11. T

    How deep do you cut dados in 3/4 plywood

    I am just about ready to start my first cabinet/built-in project. :eusa_clap I plan to use dados and was wondering how deep you cut them in 3/4 shop grade red oak. I ran some test samples with 3/16, 1/4 and 3/8 and the 1/4 looks good but I have no experience to help base my decision. PS...
  12. DaveO

    3 or 4" radius roundover bit ????

    Is there such a beast? Or what would be the best way to put a 1/4 roundover on a 4" thick timber? Dave:-)
  13. Tom Dunn

    Cutting 3/4 inch dato

    I need to cut a dado 1/2 deep, centered in some cherry stock, 2x2-1/2x14. This dato will need to accept 3/4 stock, the endgrain of some glued up panels. I do not have a dado head for my table saw. Would I be better off to use a 3/4 router bit and have on a tight fit, or to use the table saw...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top