barrel

  1. rifle_breakdown_1_

    rifle_breakdown_1_

    Early 19th century rebuild/restore piece
    • danmart77
    • Media item
    • barrel removed
    • Comments: 0
    • Album: Wayne Rifle Restoration
  2. Rick M

    30 gal. barrel or drum for dust collection ... where?

    The plan: integrate a Thien baffle with my 1HP DC. Fan will be relocated atop the baffle which will set on the barrel. All in one solution. I'll have to carry the barrel to dump it, maybe 50-60 feet, so a smaller plastic barrel around 30 gal. would be better. I'd rather empty it more often than...
  3. Wine_Barrell_Table_1

    Wine_Barrell_Table_1

    Parts made from a oak wine barrel
    • rbdoby
    • Media item
    • barrel table wine
    • Comments: 0
    • Category: Member Galleries
  4. D

    Kauri toothpick holder

    I spent most of today, and in-between choice cuss words, I managed to get this piece turned. Kauri is that stuff from New Zealand that has been buried in the peat for 40,000-50,000 years. It is mined and then specially kiln dried. I have done some inlay work with it, but this is the first...
  5. manfre

    Oak Barrel Pointers?

    I'm trying to find more information about making oak barrels. Depending on how involved the process, I might want to try my hand at making a small 2-5 gal barrel for aging beer. Anyone on here have experience making barrels or at least looked in to this and could point me toward more...
  6. mkepke

    Homemade cross-dowels (aka barrel nuts)

    As part of a repair/refurb on my workbench, I made up two cross-dowels for use in homemade vice assemblies. The barrel nuts are made up of a piece of 1" ID plain black pipe and a 5/8" acme-threaded nut. I followed this process: - cut a slot in the pipe (for the nut) using a metal-cuttting...
    • mkepke
    • Thread
    • aka barrel barrel nuts crossdowels homemade nuts
    • Replies: 1
    • Forum: "How To" Forum
  7. MarkE

    Bagging the sawdust/chips (keeping the bag in the barrel)

    I know that I have read about this before, but I am coming up empty in my searches. I want to put a plastic trash bag inside my cyclone collection barrel. What do you guys do to keep the bag in the barrel?
  8. J

    Barrel coopers out there?

    Just curious. Do we have a few coopers in NCWW that can make white oak barrels? For wine/apple cider vinegar/or a barrel for old time country store dill pickles? :dontknow: Can't use metal containers for acidic stuff unless they're stainless steel and that would have to be at least 316 SS or...
  9. dlrion

    Barrel

    Does anybody know anything about coopering? I am interested in making a small barrel, but from what I read it is a little bit tough. Has anybody ever done this before? Dan
  10. BKind2Anmls

    Pen Tip Slides Into Barrel while Writing

    I'm hoping someone can tell me what I need to do. I made a few slimline pens for friends and they tell me that, as they are putting pressure on the tip while writing, the tip gradually slides back into the barrel. Any advice? Is it something I'm doing wrong? Thanks
  11. Truefire

    Cedar barrel duck call with bloodwood insert

    Thought you guys might enjoy looking at my recently finished double reed duck call. I used cedar for the barrel and bloodwood for the insert and cut my own reeds. Needs a couple more coats of finish however.
    • Truefire
    • Thread
    • barrel bloodwood call cedar duck insert
    • Replies: 6
    • Forum: Woodturning
  12. meika123

    Have a barrel for someone

    Don't know if this is the right place for this post, but anyhoo-I have a new Fiber Barrel-just arrived this morning via UPS that I cannot use. 30 gallon capacity.It is too tall to fit under my cyclone. Still has the packing list on it. If anyone is interested either respond here or PM me. It is...
  13. JRD

    Barrel Trimer Sharpening

    Folks, After a whole lot of wood passing under my barrel trimmer, it's finally become dull. Once in the past I simply ran a file over the cutting edges two or three strokes and it was back, good as new. This time no luck. Is there a set procedure to resharpen a trimmer, or do I just purchase...
    • JRD
    • Thread
    • barrel sharpening trimer
    • Replies: 4
    • Forum: Woodturning
  14. Ralrick

    Need a Pen Barrel Trimmer - help

    I'm just getting ready to try my hand at turning a few pens. Was down in Atlanta and stopped at supply house and bought the mandrel and some blanks but they didn't have a trimmer in stock. I was looking through the Rockler catalog and it doesn't appear obvious on what I need to buy to get...
  15. Cut away barrel

    Cut away barrel

    Cut away barrel, hard to get done but looks so cool
    • kota62
    • Media item
    • barrel gun military
    • Comments: 0
    • Album: Military
  16. Full barrel

    Full barrel

    collage of a full barrel (almost 8' long & weighs 70+lbs)
    • kota62
    • Media item
    • barrel gun military
    • Comments: 0
    • Album: Military
  17. A-10 plaque

    A-10 plaque

    one of many going away presentations part of an A-10 Warthog 30mm gun barrel & 2 polished rounds + Squadron coins
    • kota62
    • Media item
    • barrel gun military
    • Comments: 0
    • Album: Military
  18. sapwood

    Glue for Barrel Hinge

    First time putting barrel hinges on small box. Certainly seems like you need to add epoxy or something so it won't fall out and I figure Tite Bond won't work on metal. It's the 5mm hinge that doesn't have a set screw for tightening as some of the larger ones do. Sure, I could find something to...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top