tenon

  1. adowden

    Wedged tenon question

    I need to attach a couple of through tenons with double wedges for the cherry buffet I am building. I have never done wedged tenons before. When I researched it, it appears there are two different ways to do it: 1) angle the mortise to allow for the expansion caused as the wedges are hammered in...
  2. Canuck

    Tenon on a Dowel ?

    I am currently working a project that calls for turning a 1/2"D by 1/2" long tenon on the ends of a piece of 3/4" dowel. My question is how to mount about an 8" piece of 3/4" oak dowel between centers on my lathe?:icon_scra Can I capture one end of the dowel stock at the headstock with my...
  3. U

    tenon dimension

    This may sound like a silly question.:dontknow: Is there any rules to dimension a tenon? For example with a 2x4 how much material would you remove? Thank you, CHO
  4. Luckbox72

    Floating /loose/slip tenon joint

    Are there any major reasons why you would use a true mortise and tenon joint of a Floating /loose/slip tenon joint? I could see if you were making a through tenon, but even then once it is glued into the mortise is there really any major difference?
  5. S

    Angled Tenon

    What is the simplest way to cut an angled tenon?
  6. froglips

    DVD: Mortise & Tenon, Kinghott $11

    Got this in the email this morning. Popular Woodworkings book store has this DVD 45% off (regular $19) now $11 Plus, orders over $25 free shipping. This link should work. http://links.mkt230.com/ctt?kn=13&m=4214383&r=Njg3MzcyMjg3S0&b=3&j=MTMyNzg2NzE1S0&mt=1&rt=0 If not, try starting...
  7. N

    Mortise and tenon joints

    I'm working on making a bed headboard for my wife. Its basically a frame with slats running vertically that will be painted in the end. I'm so new at this, I was thinking that I'm going to dowel slats in place and possibly countersink a screw for reinforcement. I was talking to my father in...
  8. Mike Davis

    Tenon jig put to use

    I want to thank PeteM for the great visit to his home, A good deal on a tenon jig and for taking me over to WoodWrangler's place. I thought I had met Jeremy before but, I guess like so many others here we knew so much about each other from this great community that we both thought we had met in...
  9. Len

    Tenon Saw Gloat?

    Found this at a yard sale for $10.00 last Saturday: I not all that familiar with tenon saws, so I'm not sure if this is a gloat or not. Brand name is "Paragon", which sounds French to me. There's a blurb about "Swedish Quality Steel" on one side of the logo, and "Diamond Sharpened" on the...
  10. B

    Accent table-first attempt at mortise and tenon joints

    This table was made as a pine prototype I made before I make two more, one out of black walnut and one out of cedar (outdoor use as a plant stand), in order to try out my ability at mortise and tenon joinery. I cut them all on my router table and they turned out pretty clean I thought. The only...
  11. Joe Scharle

    R/T Tenon Jig

    American Woodworker bought this one. Before I got a Woodrat, I used this jig for cutting tenons on door rails and still do if the 'rat is setup for something else. It's just a sled with a base, a mass block and a fence. I use a 1/2" spiral bit set usually 1" high. Pic shows side cut position...
  12. C

    tenon maker ...

    I saw a show the other day on DIY network where they made a bed out of pieces of trees that were about 4" round. They had a tenon maker that went on the end of a drill and it made round tenons. They used a variety of sizes but the largest were about 4". Where can I find something like that...
  13. Jatoba bed frame

    Jatoba bed frame

    headboard tenon
  14. B

    Mortise and Tenon Rule of Thumb???

    Is there a general rule of thumb about what dimensions to make a mortise and tenon? I've dug around a bit and I've heard that your tenons should be 1/3 the width of the thickness of the board it's going into. I couldn't really find a good answer on how long or deep they should go. If there is...
  15. L

    Help with tenon cut for trestle leg

    I am ready to cut the tenons for my trestle legs. If you remember I made these legs a short time ago. My cut wasn't exact when I finished and prepared it for glue up so I hope someone can help me learn a better technique this time. I used the dado blades in my tablesaw, the fence on the right...
  16. willarda

    Mortise nd Tenon Joinery

    On October 27, I will be conducting a one day workshop on mortise and tenon joinery. This is a handtool woodworking oriented workshop. We will learn to cut a variety of mortise and tenon joints by hand. This will include simple, simple pinned, through, through wedged. We will also use a...
  17. L

    Setup for tenon for breadboard?

    I used a breadboard on my secretary last summer so I know how to setup the tablesaw for the tenon however before making that cut on my tabletop I would like some advice. This tabletop is 38" long and 28" wide. I would like some suggestions as to how to safely and accurately setup for the tenon...
  18. H

    Need suggestions on a good Tenon Saw...

    I've finally decided to make some time as best I can to try learning mortise and tenon joinery. I have a few old chisels that should work until I can get better ones. Don't have any sort of tenon saw though and I'd appreciate any suggestions on brands, types. My budget isn't very much and I'd...
  19. rick7938

    Cutting Mortise for Loose Tenon

    I am working out the plans for shelf units for my son and his wife as a Christmas gift. I previously asked the question about the best type of joinery to use and the concensus seemed to be mortise and loose tenon. I am planning on using a router with edge quide on a jig to cut the mortises on...
  20. Nativespec

    Trend Mortise and Tenon Jig (for routers)

    Does anyone own the Trend mortise and tenon jig (about $300), or has anyone used it? Any comments? Thanks, David

Premier Sponsors

Contact for your financial processing needs!

Our Sponsors

LATEST FOR SALE LISTINGS

Top