rings

Klingspore Asheville Grand Opening

Learning from the captured ring masters!
- Hmerkle
- Media item
- Mar 3, 2015
- captured rings turning
- Comments: 0
- Category: Member Galleries
Fred's goblet

9" maple goblet with captive rings
- aplpickr
- Media item
- Jun 27, 2012
- captive goblet rings wedding with
- Comments: 0
- Category: Member Galleries
African Blackwood rings

How I do them:gar-Bi I am not rich enough to buy sticks of African Blackwood, but I was able to buy a bunch of cut off's by the pound, not good for too much but great for making thin rings. first I cut them into strips about 3/8" thick Then cut segments from them. and sand one side...
- erasmussen
- Thread
- Jul 13, 2011
- african blackwood rings
- Replies: 9
- Forum: Woodturning
Turned some rings

I burned a little bit of vacation time today to check on my bees and play in the workshop. The shop still is not wired, so I had the DC and lights on one 15 amp house circuit and the lathe on another. Good thing I didn't rewire the DC to 220v yet. I'm still quite new to turning and wanted to...
- manfre
- Thread
- Jan 19, 2011
- rings turned
- Replies: 1
- Forum: Woodturning
Poplar bowl rings

Poplar bowl rings for Poplar & Walnut bowl
- cskipper
- Media item
- Sep 17, 2010
- bowl cskipper rings
- Comments: 0
- Album: Detailed scroll work
J
"O" rings for PC 333 / 334 ROS

Recently, I needed to replace O rings that hold the dust canister on my ROS. A packagee of 100 was cheaper than buying 12 from PC / DeWalt. (I have six of those ROS's.) So I have a couple left
- junquecol
- Thread
- Aug 9, 2010
- 333 334 rings ros
- Replies: 3
- Forum: Power Tools and Their Use
rings and bases

rings and bases for 6" bowls from cut offs
- erasmussen
- Media item
- Jul 11, 2009
- and bases rings
- Comments: 0
- Album: turnings
Captive Rings (A Tutorial)

A few years ago on a forum I used to frequent, A forum member, John (aka Doghouse) did an excellent tutorial on captive rings. John needed a permanent home for the tutorial so I helped him with that. Welll, I've changed hosting services and have tried to get away from web site work since...
- Ken Massingale
- Thread
- Jun 8, 2009
- captive rings tutorial
- Replies: 8
- Forum: Woodturning
Router plate rings.... got lucky

Ok I've been using my table for sometime and its never happened. I have a generic 1/4 think phenolic router plate and I had made the center rings out of some G-10 (fiberglass board) that fit flush with the top of the plate. They basically set in the inset of the plate. I guess MOST of the time...
- greeneyedeagle
- Thread
- Mar 31, 2009
- lucky plate rings router
- Replies: 1
- Forum: Safety & Health
frame mitered segment part 3 adding rings and turning

Frame mitered segment Part 3 adding rings and turning Now that we have the base ready its time to add the segmented rings and turn. The base has been turned flat and smoothed, the first ring has also been flattened and smoothed on one side. I apply tb2 to the ring then rub it on...
- erasmussen
- Thread
- Mar 16, 2009
- adding frame mitered part rings segment turning
- Replies: 3
- Forum: "How To" Forum
Holy Growth Rings!!

Hey guys, I just cut a dead (or dying) mimosa out of my backyard and look at the size of these growth rings! I think it was a lil too close to the drainfield... The slab you see is probably 8-9 inches around, maybe 10 or better. But the rings are close to an inch! Now hows that for a fast growin...
- oderus1671
- Thread
- Mar 13, 2007
- growth holy rings
- Replies: 16
- Forum: Wood