bit

  1. wwian

    router collet too tight?

    Hey Folks! I am just now getting into learning how to use my router and router table. The router was given to me and is about 8 years old. I bought a basic set of bit and tried to use one today. However, when I went to insert the bit into the collet, it was damn near impossible to get it in. I...
  2. D

    Need custom router bit.

    Have a restoration project on a Brownstone in Brooklyn and I need to replace some molding. Does anyone know of someone who can tool routerbits to match a specific profile? Thanks
  3. M

    Need help for cutter in a tenon brace bit

    I have a tenon brace bit without a cutter ( see pictures). I have search the net but no picture or drawing of the cutter was found. Rather than trying to re-invent the wheel, I thought someone may have a picture, sketch, or source for info for the cutter. I can not stand to have a tool that is...
  4. Rhythm House Drums

    Router bit in a drill press

    Anyone ever tried this? I'm cutting some 1" holes and want them rounded over. Was thinking about putting a round over bit in the drill press and just coming down real slow. Any ideas?
  5. erasmussen

    Havent posted in a bit

    I havent posted in a bit. Here is some of the things I have been doing And what I am working on now, I guess you could call it a hybrid open and closed segments. Going to be a bit large when finished. Oh ya I took Michiko on vacation we drove to Niagara Falls and...
  6. Router bit

    Router bit

    Router bit
  7. Router bit

    Router bit

    Router bit
  8. Dutchman

    Rosette Bit

    A friend of mine asked me if I would make him some of these blocks to go at the top of the door casing in a house he is remodeling. I was wondering if someone has a router bit that will make this cut. I've looked at some online, and they are rather expensive for just 4 blocks. Does anyone have...
  9. Bas

    Gone for a bit

    I'll be out for about a week starting this Friday. Please don't break anything unless you check with Jim or Chad first :-) . Also, make sure Tracy is notified ahead of time of any unplanned outages.
  10. ErnieM

    Bosch Colt bit centering

    Just picked up a Bosch Colt palm router - used it all day and it's a great little tool. The only problem I've found concerns the centering of the bit in the sub-base opening. It's far enough off center that it can easily be seen with naked (or dressed) eye. The manual says to loosen the four...
  11. Glennbear

    Tambour Bit Set ?

    The Amana router bit set (Lonnie Bird) has been out for a while now. I recently thought of a project that would entail a tambour door and the traditional construction method holds little appeal for me. Does anyone have experience with this bit set or know of a similar set by another manufacturer...
  12. gunit1400

    I need to find a router bit

    I am currently still trying to remodel our kitchen, to include painting, refinishing cabinets, new countertop, and the like. Our home was built in 1972 and the builder used prefab cabinets. The drawers are 100% plastic and quite honestly are as ugly as homemade soap. I want to build new...
  13. Drew Roy

    Dovetail router bit choice

    :wmad: So earlier today I am in the process of running 18 dovetail boxes and a fairly new Bosch dovetail bit breaks!! There is Frued in the router now but I will pose the question to the masses..What dovetail bit have you found that will last???? Thanks in advance,
  14. kooshball

    Which flush cut router bit to "cross-cut" walnut?

    I will be cutting the top for my dresser to size soon and but it is too large to safely cross-cut on my table saw. My circular saw is terrible and doesn't have enough support to make a square cut so my plan is to cut close to the final size on the band saw or with a jig saw and then clamp a...
  15. S

    RAISED PANEL ROUTER BIT SET - $75 (NW Raleigh)

    not mine http://raleigh.craigslist.org/tls/2249158088.html RAISED PANEL ROUTER BIT SET - $75 (NW Raleigh) Date: 2011-03-05, 4:26PM EST Reply to: see below BOSCH RAISED PANEL ROUTER BIT SET INCLUDES M CARBIDE BITS: Raised panel bit: 1 1/2” cut, 5/8’ deep, ½’ shank Beading Rail...
  16. Leviblue

    Feida 115-piece High Speed Steel Drill Bit Set

    Tanga has a sale on HSS twist bits: http://www.tanga.com/products/feida-115-piece-high-speed-steel-drill-bit-set--2?utm_source=Tanga+Emails&utm_campaign=5272cd14f4-Tanga+February+2+Active&utm_medium=email I don't know anything about this but for $18.99 for 115 pc.
  17. S

    Bosch Plunge Router and Bit Set - $200 (Thomasville)

    Not Mine http://greensboro.craigslist.org/tls/2168555822.html Bosch Plunge Router and Bit Set - $200 (Thomasville) Date: 2011-01-19, 11:09AM EST Reply to: sale-77enn-2168555822@craigslist.org [Errors when replying to ads?] Router and bit set barely used. Cost new was 310 for both...
  18. Outa Square

    Southeast Tool $1 1/4" double fluted straight router bit

    Check this out... Carbide Processors is selling 1/4" shank 1/4" cutting diameter carbide tip router bits made by Southeast Tool for $1 w/ free shipping. Limit 1 per customer. There are only 50 total available at this price. Here is the link for the deal...
  19. merrill77

    Where to buy 1/4" diameter pattern bit

    I'm looking for a very small router bit - a 1/4" diameter pattern cutting bit with a short cutting length - under 1/2", but would prefer 1/4". It would be like this: http://www.rockler.com/product.cfm?page=25160&filter=pattern%20bit but only 1/4" cutting width (still with 1/4" shank)...
  20. Canuck

    Another Bit Box

    I have a considerable number of red and white oak cut-off's from the last couple of table projects. I planed a couple of pieces down to 3/8" and decided to kill some time putting together another box to store router bits. It ended up 10" long, 6" wide and 6" deep. Joinery was just 5/16" box...

Premier Sponsors

Contact for your financial processing needs!

Our Sponsors

Top