knife
-
W
Replace kitchen knife handles
Does anyone have experience replacing kitchen knife handles? I bought a few inexpensive knives today and have been thinking about restoring knives for my next project(s). The handles can be salvaged with some work, but I think replacing the handles will be better long term. Any comments? From...- Ward Green
- Thread
- handles knife restoration or upgrade scales sharpening wood
- Replies: 8
- Forum: "How To" Forum
-
Chip carving knife I made last week
The front 1/3 of the blade is scalpel sharp but the bottom 2/3rds is very dull, not sure exactly what went wrong but I need to regrind the edge. Handle is mahogany, finished in shellac and buffed with 0000 steel wool and wax. The blade is a Dewalt reciprocating blade cut and polished to 2000...- Rick M
- Thread
- chip carving knife
- Replies: 8
- Forum: Woodcarving
-
Custom Knife Block
This Custom Knife Block is 17" wide by 14" deep by 14 " tall and weighs 45lbs. Holds 59 knives, 3 steels and a pair of shears. Made from Cherry,Tiger Maple with Ebony accents- wdkits1
- Media item
- "the beast" block custom knife
- Comments: 0
- Category: 2013 Contest Winning Entries
-
Shave Horse is done
Made a shave horse today. I bought a draw knife, so I figured I had to have it. Can't wait to put it to work. http://www.youtube.com/watch?v=Uh_h_G2tQjk&feature=g-all-c- Timmy
- Thread
- draw green knife wood working
- Replies: 8
- Forum: General Woodworking
-
Riving Knife & ZC Insert
Shop made riving knife and zero clearance insert.- KC7CN
- Media item
- 64a clearance insert knife powermatic riving shop-made zero
- Comments: 0
- Album: PowerMatic 64A Riving Knife
-
Zero Clearance Insert
Custom made zero clearance insert made to accept riving knife.- KC7CN
- Media item
- 64a knife powermatic riving shop-made
- Comments: 0
- Album: PowerMatic 64A Riving Knife
-
Riving Knife Installed.
- KC7CN
- Media item
- 64a knife powermatic riving shop-made
- Comments: 0
- Album: PowerMatic 64A Riving Knife
-
Riving Knife Installed.
- KC7CN
- Media item
- 64a knife powermatic riving shop-made
- Comments: 0
- Album: PowerMatic 64A Riving Knife
-
Riving Knife Installed.
- KC7CN
- Media item
- 64a knife powermatic riving shop-made
- Comments: 0
- Album: PowerMatic 64A Riving Knife
-
Riving Knife Installed.
- KC7CN
- Media item
- 64a knife powermatic riving shop-made
- Comments: 0
- Album: PowerMatic 64A Riving Knife
-
Riving Knife Attacment.
Riving Knife attaches to original guard mount.- KC7CN
- Media item
- 64a knife powermatic riving shop-made
- Comments: 0
- Album: PowerMatic 64A Riving Knife
-
Shop-made riving knifte
- KC7CN
- Media item
- 64a knife powermatic riving shop-made
- Comments: 0
- Album: PowerMatic 64A Riving Knife
-
Shop-made riving knifte
- KC7CN
- Media item
- 64a knife powermatic riving shop-made
- Comments: 0
- Album: PowerMatic 64A Riving Knife
-
Shop-made riving knifte
- KC7CN
- Media item
- 64a knife powermatic riving shop-made
- Comments: 0
- Album: PowerMatic 64A Riving Knife
-
White Oak Knife Block
My first attempt at a simple white oak knife block.- coastal1
- Media item
- block knife
- Comments: 0
- Category: Smaller Woodworking Projects
-
White Oak Knife Block
My first attempt at a simple white oak knife block.- coastal1
- Media item
- block knife
- Comments: 0
- Category: Smaller Woodworking Projects
-
Questions About Paring Knife Handle
I have two paring knives (about 26 yrs old) that Carla really likes. One has the handle split, and I figure the other cannot be too far behind. I have already made a template, and have cut 3 handles of red oak (the only wood that was the correct thickness). 1) Does the collective NCWW...- LeftyTom
- Thread
- handle knife paring questions
- Replies: 8
- Forum: General Woodworking
-
Custom Knife Blocks--Part 4--Lots of Slots
The fronts of each block consists of 5 pieces of 3/4”stock cut to precisely the same size and all cut at a 9 degree angle on each end. Each of these sections have different slots for different size blades so a set of templates were made to use for consistency and to speed up the process...- wdkits1
- Thread
- 4lots blockspart custom knife slots
- Replies: 1
- Forum: "How To" Forum
-
Custom Knife Blocks--Part 3--Inlays
Each of the knife blocks gets a quarter circle bloodwood inlay on each side where the ends of the side pieces come together. On the prototype I made a jig to use a 2” forstner bit to cut an 1/8” deep recess for the inlay but the client wanted the inlay bigger so I bought a 3” forstner bit...- wdkits1
- Thread
- 3inlays blockspart custom knife
- Replies: 1
- Forum: "How To" Forum
-
Custom Knife Blocks-Part 2-- glue ups
One of the biggest challenges of making 25 of anything is being consistent with all of the measurements and finding ways to do glue-ups efficiently. The sides of the blocks all have to be the same size on the top dimension so when the fronts are attached everything matches up. I found out...- wdkits1
- Thread
- blockspart custom glue knife ups
- Replies: 1
- Forum: "How To" Forum