knife

  1. W

    Replace kitchen knife handles

    Does anyone have experience replacing kitchen knife handles? I bought a few inexpensive knives today and have been thinking about restoring knives for my next project(s). The handles can be salvaged with some work, but I think replacing the handles will be better long term. Any comments? From...
  2. Rick M

    Chip carving knife I made last week

    The front 1/3 of the blade is scalpel sharp but the bottom 2/3rds is very dull, not sure exactly what went wrong but I need to regrind the edge. Handle is mahogany, finished in shellac and buffed with 0000 steel wool and wax. The blade is a Dewalt reciprocating blade cut and polished to 2000...
  3. Custom Knife Block

    Custom Knife Block

    This Custom Knife Block is 17" wide by 14" deep by 14 " tall and weighs 45lbs. Holds 59 knives, 3 steels and a pair of shears. Made from Cherry,Tiger Maple with Ebony accents
  4. Timmy

    Shave Horse is done

    Made a shave horse today. I bought a draw knife, so I figured I had to have it. Can't wait to put it to work. http://www.youtube.com/watch?v=Uh_h_G2tQjk&feature=g-all-c
  5. Riving Knife & ZC Insert

    Riving Knife & ZC Insert

    Shop made riving knife and zero clearance insert.
  6. Zero Clearance Insert

    Zero Clearance Insert

    Custom made zero clearance insert made to accept riving knife.
  7. Riving Knife Installed.

    Riving Knife Installed.

  8. Riving Knife Installed.

    Riving Knife Installed.

  9. Riving Knife Installed.

    Riving Knife Installed.

  10. Riving Knife Installed.

    Riving Knife Installed.

  11. Riving Knife Attacment.

    Riving Knife Attacment.

    Riving Knife attaches to original guard mount.
  12. Shop-made riving knifte

    Shop-made riving knifte

  13. Shop-made riving knifte

    Shop-made riving knifte

  14. Shop-made riving knifte

    Shop-made riving knifte

  15. White Oak Knife Block

    White Oak Knife Block

    My first attempt at a simple white oak knife block.
  16. White Oak Knife Block

    White Oak Knife Block

    My first attempt at a simple white oak knife block.
  17. LeftyTom

    Questions About Paring Knife Handle

    I have two paring knives (about 26 yrs old) that Carla really likes. One has the handle split, and I figure the other cannot be too far behind. I have already made a template, and have cut 3 handles of red oak (the only wood that was the correct thickness). 1) Does the collective NCWW...
  18. wdkits1

    Custom Knife Blocks--Part 4--Lots of Slots

    The fronts of each block consists of 5 pieces of 3/4”stock cut to precisely the same size and all cut at a 9 degree angle on each end. Each of these sections have different slots for different size blades so a set of templates were made to use for consistency and to speed up the process...
  19. wdkits1

    Custom Knife Blocks--Part 3--Inlays

    Each of the knife blocks gets a quarter circle bloodwood inlay on each side where the ends of the side pieces come together. On the prototype I made a jig to use a 2” forstner bit to cut an 1/8” deep recess for the inlay but the client wanted the inlay bigger so I bought a 3” forstner bit...
  20. wdkits1

    Custom Knife Blocks-Part 2-- glue ups

    One of the biggest challenges of making 25 of anything is being consistent with all of the measurements and finding ways to do glue-ups efficiently. The sides of the blocks all have to be the same size on the top dimension so when the fronts are attached everything matches up. I found out...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top