Red Oak Finish Suggestions

Status
Not open for further replies.

Travis

New User
Travis
I am looking for suggestions on how to finish red oak for an indoor project. Any one who has experience and would like to share it would be greatly appreciated.

Thanks.
 

Travis

New User
Travis
It is a bookcase/display case that is 38" high by 8' and will be used as a room divider so front and back are finished. Backing is made with tongue and grove.
 

Canuck

Wayne
Corporate Member
What is "BLO"?

Travis.


I believe that Joe is referring to boiled linseed oil.

I have worked a lot of projects using RO as well. All of my "clients" (family members:wsmile:) requested a really light finish. I have used light coats of Minwax Pecan stain, followed by a coat or two of shellac; then wiping varnish. Pretty simple, but lets the grain pop as well as adding a little protection.

Wayne
 

Fred85

New User
Josh
I've used General Finishes Java gel stain to achieve a very dark brown stain on a red oak picture frame. If you're looking for a dark finish i'd recommend it, but be advised that it dries quickly.
 

Bas

Recovering tool addict
Bas
Corporate Member
It is a bookcase/display case that is 38" high by 8' and will be used as a room divider so front and back are finished. Backing is made with tongue and grove.
Lots of options for this type of project. For an "in-the-wood" finish, you can make your own wiping varnish. Mix boiled linseed oil, varnish (e.q. oil-based poly) and mineral spirits in equal parts and wipe it on with a rag. Let it sit for 15-20 minutes and wipe off the excess with a clean rag. Three coats will do it. Note that this will not give you any kind of film, nor will it give you a glossy sheen.

I did a cabinet (made out of white oak) that needed a little more protection. I first applied a coat of boiled linseed oil (wipe on - let sit 15 minutes, wipe off), then a coat of dewaxed shellac, then finally two coats of Minwax polycrylic ("water based poly"). It has held up well. I sprayed both the shellac and polycrylic, but a good brush will work just fine.

Always test your finish on a piece of scrap. Sand it to the same level as your actual project, then apply the finish. This is especially important if you're going to stain a piece, it's hard to uncolor wood.
 

Bill Clemmons

Bill
Corporate Member
Lots of options for this type of project. For an "in-the-wood" finish, you can make your own wiping varnish. Mix boiled linseed oil, varnish (e.q. oil-based poly) and mineral spirits in equal parts and wipe it on with a rag. Let it sit for 15-20 minutes and wipe off the excess with a clean rag. Three coats will do it. Note that this will not give you any kind of film, nor will it give you a glossy sheen.

This is what I use on Red Oak. It takes the reddish/pinkish tint out of the oak and gives it kind of a honey tone.

Bill
 

CDPeters

Master of None
Chris
All very good finish schedules. For red oak, especially that is showing alot of ray fleck, I like BLO - 1 or 2 coats - to make the grain "pop", then 3 to five coats of unwaxed blonde shellac, sand 320 in between. For a little "deeper" appearance, you could add a top coat or two of poly.

I think Bas mentioned test. I agree, take the time to test to get just the look you're looking for.

C.
 

Jeff

New User
Jeff
Waterlox Original Sealer/Finish is a very good, user friendly, product. It can be applied with a cloth, brush, or sprayed without dilution. It's made from tung oil. No need to wipe off the excess after coating which makes it different than many other oil based finishes. You don't need to sand between coats either. A light sanding with 220 grit before the final coat is beneficial.


http://www.waterlox.com/

Good luck and post some pics. :icon_cheers
 
Status
Not open for further replies.

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top