outfeed

  1. Outfeed Table Folded Down

    Outfeed Table Folded Down

    The small permanently attached table is 12-1/2''D x 52-1/2''W, large fold-up table is 32-1/2''D x 52-1/2''W.
  2. Motor

    Motor

    Motor shown with blade down, tilted to 45 degrees.
  3. J

    Outfeed table

    Sept. issue of Wood features an outfeed table/ assembly table that stores over the top of your contractor saw. For those who are space deprived, this may be a solution. As a plus, junk doesn't accumulate on saw top.
  4. johnpipe108

    Storage solution: outfeed table & CC sled

    For quite a while, my outfeed table and cross-cut sled have been taking up floor space when not in use (which is most of the time :oops: ); I finally realized one day that if I added some simple sockets to the underside of the outfeed table, I could store it off the floor in place of a missing...
  5. Outfeed table storage

    Outfeed table storage

    To store my outfeed table off the floor, I added simple pine sockets to fit over the storage unit support tubes, in place of a missing top shelf. My cross-cut sled sits atop the outfeed table/shelf.
  6. J

    Outfeed and router table tops

    :eusa_dancIf you are building either of the above, see posting in hot deals on laminate:eusa_clap
  7. huckster

    Outfeed Table for PM2000

    Back when I was in school the shop had a an outfeed table that was on a henge at the end of the tablesaw. So, if you need the outfeed table you pulled it up and it had henge that snapped into place when it was fully extended. The outfeed table itself consisted of a grid of rollers all about 3"...
  8. alleng

    outfeed table

    a couple of you saw the outfeed table that i added to my ridgid 3650,and asked how did i mount it.well i started with 2 pcs of 1/8 x 3'' flatbar cut to 27''. on i took off the left wing,drilled holes to match wing mounting holes to table,and installed the wing with the flatabr in between.i then...
  9. chris99z71

    Outfeed table

    So last week I actually accomplished something in the shop! A few months ago, I bought a door from Habitat. Now it's my outfeed table. In these pics, I was trying to show how the outfeed is attached to the saw. I installed two 3/8" T-nuts into the bottom of the outfeed table, threaded in...
  10. The Unisaurus

    The Unisaurus

    Not bad for $200, huh?
  11. Under side of the outfeed support

    Under side of the outfeed support

    My outfeed table is a door from Habitat with a piece of 1/2 MDF on top. Dead flat. With this picture I was trying to show how I put two 3/8" T-nuts into the bottom, threaded in some 3/8" bolts, cut off the heads, ground them to a semi-point and dropped them through some holes in the...
  12. Outfeed table

    Outfeed table

    With the ghetto support... It's a door with a sheet of 1/2 MDF on top.
  13. J

    Mounting outfeed table

    Hello All Newbie here so be gentle. I am looking for different processes I can use to attach my 14" wide extension to my table saw.I am using a piece of melamine for my extension, I will wrap the melamine with oak before installing. I just want something to cover over the motor as it is a...
  14. mshel

    Outfeed table base

    Here are a couple of pics of my new out-feed table base. A friend gave me the wood for this and since my original out-feed table was rather rickety, I decided to make one that wouldn't move. Trust me, it doesn't. I typically overdo things and it kinda shows.:lol: All members except the...
  15. Outfeed Table

    Outfeed Table

    Under side of outfeed table with mounting pad for folding leg bracket.
  16. Outfeed Table

    Outfeed Table

    Under side of outfeed table
  17. Outfeed Table

    Outfeed Table

    tablesaw outfeed table with 2 folding legs mounted to the back rail of the TS.
  18. Outfeed Table

    Outfeed Table

    tablesaw outfeed table with 2 folding legs mounted to the back rail of the TS.
  19. Outfeed Table

    Outfeed Table

    Threaded studs secure edge of outfeed table to back rail of TS.
  20. Outfeed Table

    Outfeed Table

    Threaded studs secure edge of outfeed table to back rail of TS.

Premier Sponsors

Contact for your financial processing needs!

Our Sponsors

LATEST FOR SALE LISTINGS

Top