tires

  1. charlessenf

    Delta 14-inch band saw tire (advice) sought

    Tire on the upper wheel came of this evening. From the look of the broken end, it was RED when new! It definitely shows wear - and age. However, the tire on the bottom wheel is black and, I believe, rubber. Went to Amazon and found pairs of replacement tires in Orange and Blue Urethane...
  2. Volksdad

    Setting up and tuning a ridgid 14" bandsaw

    I bought my saw in early 2006 on a closeout, and moved to NC and packed it in a shed. Earlier this month I started setting up my TINY shop, and it was time to set up the bandsaw. After my initial assessment, I finished putting it all together per the manual, and found the yellow safety key...
  3. merrill77

    Should I put on new tires?

    Naturally, since I just decided to keep the Jet - a tire came off today. The saw is about 3 years old. It appears the tire is rubber. The tire is a strip, not a circular. The ends are perfect, so is it possible this was be glued in place, not stretched over the wheel? The tires seem to be in...
  4. J

    Time for a New Set of Tires

    Today, I installed a new set of urethane tires on my bandsaw. I have found that there are two choices, either blue (Carter), or orange (all the rest.) Prices vary greatly, with Hartville having a SET of orange for $24.90. Woodcraft has the blue ones for $23.09 EACH. Klingspor's price is similar...
  5. S

    Passenger Car Tires Deal _ Need New Set

    Looking for a "KillerDeal" for Tires (Wifes Car) 60-70k miles rated Radials Size: P215/60 R17 -95T Any sales ( 3 for 1) etc........ Or Dealer recommends in Greater Cary/Raleigh area? Thanks
  6. thrt15nc

    Grizzly G0555 bandsaw and urethane tires

    Has anyone bout urethane tires on their G0555 bandsaw? I fos, what size and who'd you get them from? I called LV and they weren't too sure their 12 inch urethane would stretch far enough to go on it. I measure the wheel diameter at 13.3 inches. While I'm at it. Anyone replaced the guide...
  7. K

    changing BS tires

    I am changing the tires on my Delta 14" BS. Is it worth it to take the wheels off for ease of installation? Am I going to find unforseen trouble if I take the wheels off?
  8. Outa Square

    Bandsaw tires

    I was putting a new tire on my bandsaw. While purchasing them from the Woodworking Shop, the guy at the register said that replacing them was a chore. So when i got to my saw, i knew it would be a challenge, but i tried to stretch it over the wheel anyways. I gave up pretty quickly and took...
  9. J

    Urethane band saw tires

    Hi all, i purchased new Carter urethane band saw tires and have a question. My wheels are one inch wide and the new tires are an inch and a half wide. Must I leave a quarter inch overlap on each side and trim off, or can i trim all on one side? Or, do i need to get same width tires and my...
  10. MikeH

    Band saw tires

    I need to replace the worn out tires on my old Delta/Rockwell 10" bandsaw. I did a search on Google and came up wit quite a few places that sell them. What is your opinion on rubber vs. urethane? Where is the best place to buy band saw tires?
  11. D

    Bandsaw tires

    I've had a 20" Delta bandsaw for a lot of years. The (original) tire on the lower wheel just 'blew up' this afternoon. Half of the tire ended up in the top half of the saw, dragged there by the blade. Chunks of rubber and lots of ground up rubber dust were everywhere. The blade, by the way, is a...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top