pipe

  1. T

    Dust collector pipe

    Really considering just ordering a cyclone dust collector for the garage and was wondering where everyone got the pipe they use for all the fittings? It would start at 7" and taper to 5 or 4" to the machine... I see the kits they have but was wondering if there was anywhere local you guys have...
  2. LeftyTom

    F-Clamps or Pipe Clamps

    I am about to try my hand at gluing panels. I am building a small two-shelf "entertainment center" for LOML's treadmill room. I plan to glue some 1/2" oak to make the 17" x 24" shelves. I am using oak of varying widths, the two widest pieces at the outside edges of the panels. I have enough...
  3. rick7938

    Pipe Clamp Tips and Tricks

    Although I would love to have a shop full of parallel clarmps, my budget only allows me to have a variety of pipe clamps. They work pretty well, but they do not always clamp with the jaws parallel, so they can deflect material glue-ups such as solid panels and mortise and tenon joints such that...
  4. Splinter

    Pipe for air compressor??

    Is 1/2" or 3/4" PVC pipe okay to use for piping air from an air compressor around a shop? Anyone know of any good articles on piping air around the shop to multiple locations?
  5. ashley_phil

    Dust Pipe in Apex on eBay

    THis looks like a great deal if you are in the Raileigh area and need some pipe. http://cgi.ebay.com/Duct-Pipe-and-fixtures-for-Dust-collection-system_W0QQitemZ260305961919QQcmdZViewItem?hash=item260305961919&_trkparms=39%3A1%7C66%3A2%7C65%3A1%7C240%3A1318&_trksid=p3286.c0.m14
  6. Splinter

    Need a source for 6" flexiable dust pipe

    Anyone know of a source for 6" flexible dust collection pipe similar to the common 4" flex pipe sold by Rockler and others.
  7. Splinter

    Dust Collector pipe question

    This is like my DC.. http://www.cpojettools.com/products/710700ck.html It is a 2HP 1200 CFM at 4" DC machine. Now for the questions..... I can remove the y (for 2 4" ports) at the machine and it has a 6" port. If I was to run 6" S&D pipe out to my tools and then reduce the pipe down at each...
  8. Splinter

    DC Pipe Layout Tool

    Does anyone know of an online software layout tool that will design a layout for DC pipe based on the location of WW'ing tools?
  9. Vanilla Gorilla

    pipe clamps!!!

    So, I am looking to invest in a fair number of pipe clamps, but since I have very little experience with them, I figured I would tap the knowledge base! I don't have a lot of money, so that is certainly an issue. I also do not need clamps that are feature rich. Bare bones are fine. What...
  10. gordonmt

    looking for a deep throat pipe clamp

    I am looking for a deep throat pipe clamp. It needs to be at least 9 inches deep. I have found several 7 inch deep clamps but nothing that is 9 inches. I have pictured the 7 inch version below so you can see what I'm looking for. Can anyone help me find this critter. I have looked at all my...
  11. A

    PVC DC Pipe- a trip to the cleaners!!!!

    I am reworking the DC drops behind the knee wall in my shop as part of the autogate installation. I needed a few feet of 6" PVC S&D. Of course, as all of you who have looked know, that stuff is hard to find. I tried all the local plumbing supply, Ferguson's Waterworks, etc. here in Washington...
  12. Pop

    PVC pipe based dust collection

    Knowing I needed some sort of dust collection but not seeing too many other systems around here, I opted to use PVC pipe for my shop lines. I bought a 2hp double bag setup, replaced the bottom bag with a clear plastic bag and made a remote on/off switch that sets above my workbench. After...
    • Pop
    • Thread
    • based collection dust pipe pvc
    • Replies: 19
    • Forum: Safety & Health
  13. air force 1

    3 Box Joint Jigs in a 3/4"x24"PVC pipe

    I was having coffee this morning and had a brain storm. You see all them jigs in your shop, what if you could put three of them in a 3/4" PVC pipe about 24" long? And mount them on the side of your router table. Go down to the hardwear store and buy three square rods, 1/2" - 3/8" and 1/4" (or...
  14. scsmith42

    "Almost free" 6" metal duct pipe

    A friend of mine is looking to unload several hundred feet of 6" metal duct pipe. He contacted me today to see if I wanted it; otherwise it's going to the scrap yard later this week. The pipe is new, but was removed from some appartment buildings due to a code problem or something. It was...
  15. rick7938

    Pipe Clamp 101

    I am saving my pennies to outfit my shop with the Bessey parallel jaw clamps as I can afford them. For now, I am working with some Irwin pipe clamps that work OK, but has shown me that I need some help with manipulating these things. Sometimes they seem like I'm wrestling an octopus while trying...
  16. Jim Murphy

    6" PVC D-2729 pipe source

    John Deere Landscapes of Apex, at 919-303-7290 is a stocking dealer for Cresline pipe, and can order the PVC you need for your dust collection system. The Cresline part number is 52155. Here's the Cresline datasheet for the pipe...
  17. Bas

    Where to buy 6" S&D PVC pipe

    I'm looking for a local supplier of 6" Sewer and Drainage PVC pipe. I don't need much, maybe 40 feet or so. I also need fittings, mainly wyes and 45 elbows. Those wyes are expensive! The cheapest online source I've found so far is at Polsteins' -> http://www.homeandbeyond.com/prod-0077239.html...
  18. Tarhead

    Pipe Threader in the CLT Area?

    I found some 3/4" stainless steel and regular steel pipe at a salvage yard and want to make clamps out of it. Can the stainless be threaded? Does anyone have a pipe theader that could help? Thanks! Mark
  19. UP Half-set, complete

    UP Half-set, complete

    A UP half-set has drones, but is without the chord-pipes called regulators (roughly corresponding to the chord buttons on some accordions). I made these in 1983, using Mexican rosewood (cocobolo) scraps given by a friend who got them from her woodturner-boyfriend. The main stock is of birch...
    • johnpipe108
    • Media item
    • bagpipe half-set pipe uilleann
    • Comments: 0
    • Album: Irish Uilleann Pipes -- Half-Set
  20. GeorgeL

    Source for 6" S&D PCV Pipe for DC ?

    I am in the process of setting up the ducting system for my dust collector and I having a bit of trouble locating 6" S&D PVC pipe in the Fuquay area. Anyone know of a plumbing or pipe supplier that carries 6" S&D? Thanks, George

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top