knot
-
Celtic Knot for Me, too...
I didn't want to high jack Sawduster's thread, so here's mine. I made this pen in March of 2011. I made the cuts on a 10" miter saw by holding the blank against a board which I had mitered at 30 degrees. In case you can't visualize that, that is my fingers WAY too close to a 10" saw blade...- allisnut
- Thread
- celtic knot
- Replies: 6
- Forum: Woodturning
-
Finally, a celtic knot
I have been trying to pull this off for the better part of 3 weeks now....making a jig, making it again and again :BangHead: tweaking my table, my drilling jig , putting lifts in my shoes ...wearing no shoes at all , you get the idea . This is the closest I have come so far . The pen is walnut...- sawduster
- Thread
- celtic finally knot
- Replies: 12
- Forum: Woodturning
-
celtic knot
- sawduster
- Media item
- celtic knot
- Comments: 0
- Category: Member Galleries
-
Celtic Knot
Hello NCWW's, I have made a Celtic knot pen before after seeing Alex's Video. But has anyone turned a Celtic knot in a Bowl blank solid or Segmented Turning? It just came to me and sounded really good in my head~! :widea: :dontknow:- MrAudio815
- Thread
- celtic knot
- Replies: 3
- Forum: Woodturning
-
L
Filling knot holes in knotty pine
Does anyone have any suggestions as to what to use to fill holes in knotty pine? I can pick around and sellect areas of the boards that don't have the holes but thought if I could find something that would fill the holes and look nice I would do that. Waste not want not you know? I am looking...- lwhughes149
- Thread
- filling holes knot knotty pine
- Replies: 13
- Forum: Finishing
-
IMG_6987_1024x768_1
- AlexL
- Media item
- burl celtic jarrah knot
- Comments: 0
- Category: Member Galleries
-
IMG_6984_1024x768_1
- AlexL
- Media item
- burl celtic jarrah knot
- Comments: 0
- Category: Member Galleries
-
IMG_6982_1024x768_1
- AlexL
- Media item
- burl celtic jarrah knot
- Comments: 0
- Category: Member Galleries
-
IMG_6981_1024x768_1
- AlexL
- Media item
- burl celtic jarrah knot
- Comments: 0
- Category: Member Galleries
-
Aluminum & Walnut Celtic Knot
Hi everyone, I haven't been around in a while I've been really busy since the story came out in the newspaper. I wanted to show some of my newer pens. This is a european in big leaf maple burl. The celtic knot is walnut laminated between two thin strips of aluminum. Th finish is ca. This is...- AlexL
- Thread
- aluminum celtic celtic knot knot walnut
- Replies: 24
- Forum: Woodturning
-
A
Celtic Knot
Since there has been some turning threads lately, I thought this may be of interest. Many (most?) of you turners probably already know how to make a Celtic Knot, but I thought it was neat. A friend on another forum who lives in Tokyo just made his first Celtic Knot pen turning. I have seen...- Alan in Little Washington
- Thread
- celtic knot
- Replies: 8
- Forum: Woodturning
-
S
Knot holes
Im looking for a clear epoxy knot hole filler. I want to be able to fill the knot holes flush and then apply a varnish on top. I want to be able to see all the knots and imperfections so i do need to keep it clear but i need to color the first layer so you cant tell it is a veneer (1/4 ")... -
Yep another knot
This is the first one I cut on a bandsaw (45 degrees), Red Oak with Walnut knot, slimline kit. And this is my first Cigar, use some nice Sapelle. Both with CA finish that I'm still trying to perfect.:BangHead: Also working on how to take better photos.- bluewing92
- Thread
- knot yep
- Replies: 1
- Forum: Woodturning
-
G
OMG, Knot another knot
I built a new miter sled at 55 degrees and tried it with a thinner blade. I like the higher angle and thinner blade more than the 45 and standard kerf blade. This is a Gold Artisan Cigar dressed in figured Sapelle with a hard maple 4-ring knot. The pen is finished with CA, MM, and buffed out...- Gary G
- Thread
- knot omg
- Replies: 12
- Forum: Woodturning
-
Celtic Knot
My first try at this type of thing. A little scroll sawing, a little carving, and a little woodworking. The wood was extracted from Woodguys' trash pile after his dovetail class a few months ago (Thanks John!) and the Celtic idea came partially from Cathy's work (Thanks Cathy!) and partially...- PeteM
- Thread
- celtic knot
- Replies: 13
- Forum: Scrollsaw Work
-
Celtic knot trivet
Okay, Michael, I posted this for you. This is a trivet that I made initially as a regular trivet. My brother-in-law said "Wouldn't it be cool if you shaped it so it looks like rope?!" So, mostly with sandpaper, and sitting in mom's hospital room this came as close as will ever to looking like...- cskipper
- Thread
- celtic knot trivet
- Replies: 24
- Forum: Scrollsaw Work
