fit
-
Wip dry fit
I've been working on this Hepplewhite style dressing table for a few weeks now and finally got to the dry fit stage. I saw one in an antique store last year and was able to get a couple of very poor pics and a few measurements before the store owner started giving me the evil eye. I quess I...- Larry Rose
- Thread
- dry fit wip
- Replies: 10
- Forum: General Woodworking
-
Proper fit for dado's and rabbits?
I am making some kitchen cabinet. The upper cabinet assemblies are making me crazy! I took the time to cut all the pieces. The cabinets are assembled with dados, rabbits, glue, and brads to hold it all together while the blue dries. I took the time to set up my dado cutter on the table saw and...- bluchz
- Thread
- dado fit proper rabbits
- Replies: 8
- Forum: General Woodworking
-
Wip dry fit
View image in gallery I've been working on this mahogany coffee table for SWMBO for much too long now. I've obviously got a lot of sanding and fitting left before the finishing room View image in gallery- Larry Rose
- Thread
- dry fit wip
- Replies: 15
- Forum: General Woodworking
-
Mission tables, red oak, dry fit
Mission tables, red oak, dry fit- bwat
- Media item
- dry fit mission oak red tables
- Comments: 0
- Category: Member Galleries
-
Hope All These Parts Fit
Here's Roscoe, a WIP. First time I've tried to carve separate parts and fit them together. As you can see, it allows you place the head in different positions. The bust will be mounted on a stand attached to a base. Now I have to decide what color outfit he has on. Will post when completed...- Woodchuck
- Thread
- fit hope parts
- Replies: 5
- Forum: Woodcarving
-
J
Main page don't fit
Last few weeks I noticed the main page no longer fits in the browser. I'm afraid if I re-size it I won't be able to read anything cause the print will be too small. Actually you'll see several things are all whacked up in this picture... it's way over crowed, I'm starting to get confused...- jeff...
- Thread
- fit main page
- Replies: 10
- Forum: Help Desk
-
Excelsior? It's not slippery; this just might fit better
Yeah, right. :rolleyes: Anyway, I will be just a few minutes away from the Sandy Springs Rockler for Thanksgiving. Check out page 4 of their ad: http://www.rockler.com/Retail/flyer/Nov08b2/4.pdf Hmmm... When I consider that I really need a better motor on that old lathe (so I really need...- CarvedTones
- Thread
- excelsior fit slippery
- Replies: 16
- Forum: Woodturning
-
Cypress Bench Dry Fit WIP
This is the result of my last few days in the shop. Now I got to take it apart and start sanding. I will use a marine grade varnish to finish . It goes to the local Garden Club for thier fund raising auction. More when finished.- Larry Rose
- Thread
- bench cypress dry fit wip
- Replies: 11
- Forum: General Woodworking
-
Trash Can Lid Separator Fit???
Hey gang, I ordered one of the trash can lid separators and it says it fits a standard 20" can. Well, after dragging it through the store and trying it on each variety at the BORG, I still couldn't find one that seemed to fit properly. Question: Is there supposed to be a snug fit or does...- MikeL
- Thread
- fit separator trash
- Replies: 21
- Forum: General Woodworking
-
demilune fit for scrap - gutted
Well the table was almost finished, sanded with micromesh till it gleamed. Ebony legs looking sensational, all that was left was to pour the resin into "Jordan lake" What B#$$d invented that #$$% polyester resin? I researched the web, I made test pours in scrap lakes, I read all the instructions...- DavidF
- Thread
- demilune fit gutted scrap
- Replies: 31
- Forum: General Woodworking
