brass

  1. F

    Brass plate around the Hickory area

    I am looking for a source for 1/8" brass plate in western NC; google has not helped me :evil: I'm assuming 1/8" is what i need, it would be for small parts on various jigs and whatnot.
  2. Joe Scharle

    3/16" Brass rod around Raleigh

    Anyone know where I can find some 3/16" brass rod?
  3. S

    where to buy small brass knobs?

    .
  4. Mark Gottesman

    Looking for Brass strip in Winston-Salem for a Banjo

    I have a need for a strip of brass for a Banjo Tension hoop. Would like to find it locally if possible since I don't know who sells small order things like this. I can get it from Graingers. Needs to 3/16" thick x 1/2" tall x 36" long. Needs to be soft or half hard anneal as I will need to...
  5. eyekode

    5/8" brass rod for plane adjusting hammer?

    Any recommendations of where to buy some 5/8" brass rod in the Apex/Raleigh/Durham area? I would like to make plane adjusting hammer for the wood plane(s) I am finishing up. Thanks! Salem
  6. christopheralan

    Will CA glue bond brass casings to spray varnished wood?

    I am putting the finishing touches on a 1911 display case and the customer wants 45cal's attached to the plaque. Hot melt glue didn't hold, as expected, so I tried Gorilla Brand CA glue. So far so good, but will this hold? Thanks!
  7. Trog777

    Brass screws

    Whenever I use brass screws, I like to thread a steel screw in first to cut the threads. Problem is, half the time I can't find the size I need. What I want is a a set of threaded screw pilots. Maybe with tee handles? Long enough so you could just screw it in as far as the screw length you were...
  8. mlzettl

    Brass box hinges

    For a number of years, I have used Brusso hinges for all of my small boxes, cabinets, etc. They are without a doubt among the finest available. The only problem is that they are very expensive. I have tried other hinges from time to time, but have always been disappointed. Not too long ago, I...
  9. michaelgarner

    Handmade Brass Sliding Bevel

    Just wanted to share this sliding bevel that I made. The brass came from a kit and I used tiger maple for the stock. I really enjoy using this tool (worked wonderfully laying out dovetails, I'm practicing so I can finish my tool chest). The only regret is that I didn't order more brass kits...
  10. F

    Looking for 1/8" brass sheet

    Hi, Just finished the Woodsmith block plane, a joy to use. It comes with a Hock blade, adjustable by tapping... Now wonder where locally (Raleigh, NC) can I find some 1/8" brass sheet stock (2 pieces 1/8x3x8 should work)? Thanks in advance. Pinwu Editted 02/10: Thanks for the...
  11. JRD

    Brass Screw Removal

    I'm looking for ideas, tips, hints, etc. on removing broken brass screws from a wooden box that I'm making. One, has broken off just above the wood surface, two are flush with the surface of the wood. My first thought, other than a few choice words, was just drill them out, but I want to...
  12. Sanders Fine Woodworking

    Brass pins/rod

    I am making some boxes with wooden hinges and want to use brass for the hinge pins. Does anyone know a good source of supply?
  13. Eaglesc

    Brass confusion

    Sorry about the lousy picture, I still have pens to finish before the Washington show
  14. TV Stand - Cherry

    TV Stand - Cherry

    brass pulls fumed for 24 hours in ammonia
    • kota62
    • Media item
    • brass cherry tv
    • Comments: 0
    • Album: House
  15. B

    need brass rods

    I'm restoring a baby grand piano and need to replace missing brass rods on pedal action. I already checked Reid and they don't have round brass rods, anyone know where I can find some ?
  16. johnpipe108

    Woodwind proto with brass keys

    My Irish Uilleann pipe baritone regulator prototype now has keys; the first one was a quick "git 'er done" variation on the traditional block-mounted teardrop key. Block-mounted keys are a lot more tedious to make; a proper one requires a lot of forging and filing to come up with an attractive...
  17. BobN

    Brass

    I need some 14 gauge brass for a project I am working on. Anyone know where I can get some. Bob
  18. michaelgarner

    3/16" Brass

    Hey everyone I was wondering if anyone knew of a supplier for brass stock. I am looking for 3/16"X3"X3'. I know of McMaster-Carr that sells it in the size i want but is charging $80.00. For the guys that are smarter than me concerning different types of brass it is listed as Ultra-Machinable...
  19. Humidor open

    Humidor open

    Humidor with lid open. Solid brusso brass quadrant hinges (not cheap!).
    • Wes
    • Media item
    • brass brusso cigar hinge humidor quadrant
    • Comments: 0
    • Category: Member Galleries

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top