crown

  1. charlessenf

    Installing Cathedral Crown Molding Help

    I watched Gary Katz videos*** on Installing Crown Molding on a flat ceiling and was seriously impressed by his approach to teaching the concepts and important points. After spending several hours 'on the net' without finding anything (of a similar quality) on installing Crown on a Cathedral...
  2. P

    cutting crown on the flat need angles for 10*

    I need to cut crown molding on the flat for angles 10* to the vertical and 808 TO THE HORIZONTAL WITH 90 DEGREES WALL ANGLE help
  3. S

    miter saw settings for crown moulding??

    I am attempting to wrap the top of a 12' x 1' bookcase in crown moulding. Since I only have a limited amount of crown, I can't do a lot of experimenting. :BangHead::BangHead: Can someone tell me what miter saw settings to use for the corners and to join two pieces on the front? Thanks!
  4. W

    Crown on a Bandsaw Tire

    I need to replace the old rubber bandsaw tiles on my bandsaw.The old tiles have crowns on them. But, the new urethane tiles don't. The question is: Can I put them on? Will the blade track okay? Thanks for all answers. Have a nice and quite Sunday. Qui
  5. Mt. Gomer

    Porter-Cable NS100 18-Gauge Narrow Crown Stapler

    $25.99 shipped @ http://fastening.tooliday.com/
  6. S

    PorterCable Recon 18Gge Crown Stapler -$25

    www.tooliday.com PorterCable NS100B Factory Reconditioned 18Gauge Narrow Crown Stapler Bare Tool Mar 19, 2010 01:00 am The Porter-Cable NS100BBR Factory Reconditioned NS100B 18-Gauge Narrow Crown Stapler Bare Tool is a pleasure to use with plenty of convenient features and a comfortable...
  7. Crown Mark Knife

    Crown Mark Knife

    Crown Mark Knife
    • Splint Eastwood
    • Media item
    • crown knife mark
    • Comments: 0
    • Album: Shop Photos
  8. S

    Crown RightHand Mark Knife-$10 Amazon

    http://www.amazon.com/Crown-112-2-Inch-1-Inch-Marking/dp/B001V9KOTQ/ref=sr_1_1?ie=UTF8&s=hi&qid=1264537250&sr=8-1 Free ship to Amazon Prime members! M
  9. J

    Crown moulding

    uggg... I had a fight with the devil yesterday installing crown moulding in the upstairs hall. I haven't done enough of it to be any good at it and all those freaking angles in this old house about drove me batty. I bow to you trim carpenters out there, you have my utmost respect :notworthy...
  10. ebarr

    Crown of Thorns complete

    I have been through some difficult times over the past few months and have not felt like being in the shop. I saw this pattern and it inspired me to get off my butt and do some work. It's not perfect by a long shot, and I would like to do a few more over the next month or so for gifts. But it...
  11. johnpipe108

    Crown molding wood ID?

    I have these flat-faced crown molding pieces, which I've rabbeted for making into jewel boxes. I've been trying to identify the wood (these pieces were part of a donated batch of "firewood"), and have come up with possibilities of walnut sapwood or maybe poplar. Note the light-colored...
    • johnpipe108
    • Thread
    • crown molding wood
    • Replies: 12
    • Forum: Wood
  12. DIYGUY

    In the market for a crown stapler

    Anyone have a recommendation on a 1/4" crown stapler? I have seen the new Milwaukee 7155 and it appears to be a very nice tool - the oil-less operation is especially appealing. I cannot help but wonder about its lifespan however. I have the usual mix of brad nailers from PC and a DeWalt finish...
  13. WoodWrangler

    Best Place to Buy Crown Molding around Charlotte?

    Figured this would be the best place to ask ... where is the best place to buy crown molding around Charlotte? A buddy of mine wants to put crown in his house and I think the big box store prices seem a bit high.
  14. small bathroom shelf

    small bathroom shelf

    Made out of a scrap piece of crown molding.
    • Sully
    • Media item
    • crown molding shelf
    • Comments: 0
    • Category: Member Galleries
  15. J

    Maple Crown

    I need about 25 ft of maple crown about 2 1/2 wide . In the Raleigh area. Thanks Dwight
  16. jaustin

    basboard molding, crown molding ....

    Anyone have a good source on buying molding? I am getting ready to redo a whole house and trying to find somewhere besides the borgs that i can get a better price? online would be fine as long as the shipping doesn't kill the savings.
  17. Jon

    Crown molding How to?

    Anyone wanna teach me how to do Outside corners on a Cherry Cabinet?
  18. nelsone

    Crown Finish Question

    I will be topping the library unit I am building with crown moulding. The room has no crown in it at this time and the room is being used as an office. My clients want crown all the way around the room, but are questioning how to finish it. The crown in the rest of the house is painted white...
  19. P

    crown molding cut flat

    I have always cut crown molding the normal way on a miter saw. i would like to try and do it flat because the size does not fit the saw.I looked on the net for the compound angle charts but was wondering if anyone has had experience using these
  20. DaveO

    Best way to cut crown moulding??

    I am close to the point in building of my wife's Xmas kitchen hutch where I'll be cutting the crown moulding for it. I have never done crown before :5dunce: and would rather not have to make to many practice cuts in $3.00 a l.f. moulding8-O I did by a cheap piece of MDF crown to practice with...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top