angle

  1. block plane

    block plane

    • smallboat
    • Media item
    • angle block find low plane
    • Comments: 0
    • Album: Bench improvements
  2. block plane

    block plane

    • smallboat
    • Media item
    • angle block find low plane
    • Comments: 0
    • Album: Bench improvements
  3. block plane

    block plane

    • smallboat
    • Media item
    • angle block find low plane
    • Comments: 0
    • Album: Bench improvements
  4. block plane

    block plane

    • smallboat
    • Media item
    • angle block find low plane
    • Comments: 0
    • Album: Block Plane
  5. block plane

    block plane

    • smallboat
    • Media item
    • angle block find low plane
    • Comments: 0
    • Album: Block Plane
  6. block plane

    block plane

    • smallboat
    • Media item
    • angle block find low plane
    • Comments: 0
    • Album: Bench improvements
  7. Low-angle bench plane

    Low-angle bench plane

    After a proper sharpening and a few minutes of setup, it effortlessly made thin curly shavings on this red oak.
    • merrill77
    • Media item
    • angle jack low plane veritas
    • Comments: 0
    • Category: Member Galleries
  8. J

    Adjustable angle table top

    Just playing around with a conceptual idea for a friend of mine. The top should be adjustable from 0-90 degrees at any angle. This is kinda like a trammel with a fixed pivot point at the top. As the top is raised a bolt slides along the two channels and gets locked in place somehow. I haven't...
  9. M

    Plane with compound iron angle

    Identified plane problems: I have observed that cutting a rabbit has a tendency to creep causing the rabbit to narrower with depth. This may be my skill in cutting a rabbit with a hand plane. Also I have noticed that when surface planning, I as well as others skew the plane so as to attack the...
  10. CrealBilly

    How bad can a cheap angle grinder be?

    Against my own better judgement, I purchased a cheap 'made across the pond' angle grinder. Problems after no more than five minutes of use: A screw had vibrated out from the gearbox to motor connection and was completely missing - I could not find the screw anywhere, it may have been...
  11. DeWalt right angle drill

    DeWalt right angle drill

    • bobby g
    • Media item
    • angle dewalt drill right
    • Comments: 0
    • Category: Member Galleries
  12. A

    Hard to set the bevel angle on your CMS/SCMS?

    Y'all remember me attaching a short arm to the tilt mechanism on the front of my tablesaw and mounting a little angle gauge on it for a digital blade tilt indicator? At that time I said I was gonna do something similar for my mitersaw. I did, but never got around to posting it, so here it...
  13. Ehardin

    Angle Iron

    Not exactly woodworking but will end up a ww project. Im looking for a source of angle iron in the Winston Salem area... Anybody know where I can fin some??
  14. sawduster

    angle drill opinions please

    Anyone have one of these or know anything about them ? http://www.woodworkingshop.com/cgi-bin/67A1CB88/mac/additmdtl.mac/showItemDetail?item=TZ20000&sku1=Y&shipRemaining=0&daysBetween=0&daysBetweenFix=0&monthsBetween=0 my primary use would be bowl sanding on my lathe . I have a little "...
  15. A

    New Angle Gauge

    This is a follow-up to my post about using a tilt gauge with your TS to give you a precise, easy to read readout of blade tilt. The little Wixey angle gauge I used worked well, but I just got a better one: It's the NEW Wixey and a little larger than the old one: This one is chock...
  16. CrealBilly

    Right Angle Triangles

    I need to cut a bunch of right angle triangles that vary in size from 1 1/2" x 1 1/2" to 3/8" x 2". The triangles will be used for inlay and only need to be a 1/8" thick to stand a little proud for flush sanding. Has anyone made a TS jig, knows of a jig or has some ideas that would make these...
  17. BKind2Anmls

    Digital Remote Readout 35" + FREE Digital Angle Gauge

    Upgrade your table saw to an easy to read digital display! Get inch (decimal or fractional) and millimeter (metric) readings from 0" to 35". Features magnetic back remote readout unit with 52" cord that you can mount or move almost anywhere. Easy to assemble, easy to use! Mounting hardware...
  18. eyekode

    Wooden/low angle spokeshave

    I have never owned or used a spokeshave so who knows why I thought I could make one. But eventually I want to build some chairs and I have heard a spokeshave can be handy :). View image in gallery Anyway I picked up a Hock iron from http://www.craftsmanstudio.com/. They have good prices and...
  19. M

    20 degree angle on chisles??

    I got several chisles at a garage sale yesterday that are ground to a 20 degree angle. the faces of all the chisels were chipped and look like they had 32 tpi on the face. well I cleaned they up and tried one, edge rolled and chipped , the chisles have a blade about 6 inches long and thin. all...
  20. D

    Angle Grinder Info

    I'm entertaining the idea of getting a small angle grinder. I'm looking at these: DeWalt 4 1/2" http://www.homedepot.com/Tools-Hardware-Power-Tools-Reconditioned-Tools/h_d1/N-5yc1vZ1xr5Zbcsh/R-100401582/h_d2/ProductDisplay?langId=-1&storeId=10051&catalogId=10053 Ryobi 4.5"...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top