vice

  1. kenhickswoodworker

    Pattern Makers Vice For Sale

    Pattern Makers Vice $200 See Highland Woodworking for details and installation instructions. Comes with everything that was in the box. I had this on my adjustable height bench and it was too heavy to be lifting up and down. I may have used it once or twice but I don’t think so. I never even...
  2. Leg vice

    Leg vice

    • merrill77
    • Media item
    • build clamp leg pipe vice workbench
    • Comments: 0
    • Album: Workbench build
  3. Leg vice - top screw

    Leg vice - top screw

    • merrill77
    • Media item
    • build clamp leg pipe vice workbench
    • Comments: 0
    • Album: Workbench build
  4. Leg vice - extended

    Leg vice - extended

    • merrill77
    • Media item
    • build clamp leg pipe vice workbench
    • Comments: 0
    • Album: Workbench build
  5. Leg vice - bottom screw

    Leg vice - bottom screw

    • merrill77
    • Media item
    • build clamp leg pipe vice workbench
    • Comments: 0
    • Album: Workbench build
  6. EndVice

    EndVice

    • merrill77
    • Media item
    • clamp end pipe vice
    • Comments: 0
    • Album: Workbench build
  7. EndVice-side

    EndVice-side

    • merrill77
    • Media item
    • clamp end pipe vice
    • Comments: 0
    • Album: Workbench build
  8. EndVice-end

    EndVice-end

    • merrill77
    • Media item
    • clamp end pipe vice
    • Comments: 0
    • Album: Workbench build
  9. EndVice-bottom

    EndVice-bottom

    • merrill77
    • Media item
    • clamp end pipe vice
    • Comments: 0
    • Album: Workbench build
  10. Workbench build - face vice

    Workbench build - face vice

    This block on the face of the rear pipe clamp engages with the slot on the benchtop to resist twisting of the pipe clamp and support the pipe clamp when fully extended
    • merrill77
    • Media item
    • clamp pipe vice workbench
    • Comments: 0
    • Album: Workbench build
  11. Workbench build - face vice

    Workbench build - face vice

    In the fully extended position
    • merrill77
    • Media item
    • clamp pipe vice workbench
    • Comments: 0
    • Album: Workbench build
  12. Workbench build - face vice

    Workbench build - face vice

    Fitted wooden blocks and screws serve as a latch to hold the face to the pipe clamp face.
    • merrill77
    • Media item
    • clamp pipe vice workbench
    • Comments: 0
    • Album: Workbench build
  13. Workbench build - face vice

    Workbench build - face vice

    View of the pipe clamps from the bottom of the bench
    • merrill77
    • Media item
    • clamp pipe vice workbench
    • Comments: 0
    • Album: Workbench build
  14. Workbench build - face vice

    Workbench build - face vice

    Two UHMW strips are inserted into each hole to conteract the tendency of the vice face block to tilt back on the pipe. You can see one strip at the bottom of the holes on the inside face. There is an additional strip on the top of the outside face. The pair tilts the face block forward slightly...
    • merrill77
    • Media item
    • clamp pipe vice workbench
    • Comments: 0
    • Album: Workbench build
  15. Face vice built with pipe clamps

    Face vice built with pipe clamps

    • merrill77
    • Media item
    • clamp face pipe vice
    • Comments: 0
    • Album: Workbench build
  16. Face vice built with pipe clamps

    Face vice built with pipe clamps

    • merrill77
    • Media item
    • clamp face pipe vice
    • Comments: 0
    • Album: Workbench build
  17. hymie123

    Jorgensen 41012 - 12" Rapid-Acting vice clearance?

    I am in the process of building a workbench and am planning to use the Jorgensen 41012 bench vice Does anyone know what clearence is required between the edge of the bench and legs/support? I haven't been able to find anything regarding the detailed dimensions of this vice. Thanks Jim
  18. P

    florsent lighting for a handsaw vice

    Does anyone have any suggesions related to where I could purchase a good circular florescent light for my acme handsaw vice?
  19. sash plane

    Front vice, Right hand vs. Left hend...

    Why it the front Vice always on left hand side.... I'm right handed , but to me..?? It would feel better if the vice was on the right had side, for say cutting dove tails... or anything else...for that matter... I'm in the process of adding a front vice to my bench and have not placed it...
  20. K

    Looking for a vice for a workbench

    I'm looking for vice I can use for both front and sides for my 36"x20" knockdown workbench. Since it isn't large I was trying to find something for the scale of the bench. Does anyone know how the woodriver vice is? http://www.woodcraft.com/Product/2004875/7501/WoodRiver-Small-Front-Vise.aspx...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top