spiral

  1. H

    Sooo....I was the hi bidder. lol Will inventory, what I am not going to use in garage & post for sale soon.

  2. BKHam

    anybody have a cutech "spiral" head planer?

    My situation: I would like to have a helical spiral head on at least a planer for all the reasons that anybody else would get one...quieter, easily replaceable, less tear out. I have the Dewalt 735 with straight knives. I have a older powermatic 8 inch jointer as well. i could sell both...
  3. jonnyfontaine

    Grizzly spiral cutter versus bryd Shelix cutter

    I own a grizzly 8" jointer and I can't square the edge of a board, I think some of the knives are higher on one side quite a bit. And since the gibs seem welded on I'd rather not go through the nightmare of adjusting the knives. I ordered a bryd Shelix cutter head a while back but they say...
  4. C

    Spiral Staircase Around Log

    I'm talking with a builder about a spiral staircase with two landings around a flared cypress log, and I'm trying to wrap my head around laying out for joinery as well as find something techniques for strength and consistency. I've got a few ideas, but I'm wondering, does anyone have any...
  5. T

    6" & 4" spiral pipe and fittings

    I am looking for approximately 60-80' of 6" spiral pipe and approximately 40' of 4" spiral pipe to help finish assembling my dust collection system. In addition, I will need 6x6x4" lateral y's. If you know of anyone that has some of these products would you please send them my way via email...
    • Temp626
    • Thread
    • collection collector cyclone duct ductwork dust fittings hose lateral pipe piping reducer separator shopvac spiral vacuum
    • Replies: 2
    • Forum: Where Can I Find, Buy or Sell?
  6. T

    6" Spiral Duct Needed

    If anyone has any 6" spiral duct or knows of anyone that is interested in selling what they have leftover, I am interested in approximately 60' of that pipe. Best way to contact me is my email...... temp626@aol.com........... Thank you for the help, Tom Empie Concord, NC
  7. T

    Metal Ductwork Suggestions

    I live in the Charlotte/Concord, NC area and was wondering if anyone knows where I might find a reasonable supplier for metal duct for my dust collector. I will be using approx. 80 feet of 6" duct and enough 4" for approx. 10 drops. I will also be looking for 3 6" blast gates and approx. 10-12...
  8. S

    Jet vs Grizzly Jointer/Planers with spiral heads

    Trying to decide which to buy. The griz is about $650 cheaper than the Jet. The griz has a 5 hp motor while the Jet has a 3 hp motor. The griz head is 3 1/8 in diameter with 32 cutters. The Jet head is 2 3/4 in in diameter with 56 cutters. The Jet has a fractionally shorter conversion time in...
  9. DWSmith

    Grizzly Spiral Head Jointer Cutter Replacement

    I have owned four jointers; a Delta 4", Jet 6", PowerMatic 6" and now a grizzly 8". The first three, Delta, Jet and PowerMatic all shared the same fault, blade changes that would make the Pope cuss a blue streak. Maybe I am to anal but I had to spend an insane amount of time changing and...
  10. X

    Leitz solid carbide spiral routers ($20)

    http://www.forums.woodnet.net/ubbthreads/showflat.php?Cat=&Number=4868616&page=0&view=collapsed&sb=5&o=
  11. X

    Leitz TCT router bits and solid carbide spiral routers

    Just thought I'd give you folks a heads-up on these Leitz bits : http://www.forums.woodnet.net/ubbthreads/showflat.php?Cat=&Board=UBB4&Number=4809209&fpart=&PHPSESSID= Thanks, MJ I added another tread with more items...
  12. decibel

    Spiral cutterhead questions

    I've been playing around with the new jointer/planer a bit and had a few general questions about they spiral cutter head. First off I noticed in the manual it does speak about adjusting the outfeed table of the jointer but says it only applies to straight knife version? Was curious to why it...
  13. gdoebs

    New jointer - spiral or straight?

    I've been joking with my wife that I want to buy a Grizzly G0609 12" Parallelogram jointer for Christmas. She always kinda laughed at me...until this last weekend. I mentioned getting something else instead and she said "I thought you were getting that new jointer."! :tool: So I guess it's as...
  14. Trent Mason

    Spiral staircase handrail

    I was talking with my boss this afternoon and he built a spiral staircase over the weekend in his cabin. The center post is a dried cedar tree trunk. The steps and balusters (?) are walnut and they are all in place. The only thing he couldn't figure out is how to make a handrail. Of course...
  15. Spiral Walnut and Cherry

    Spiral Walnut and Cherry

    Spiral segmented bowl of walnut and cherry (13” x 4.5”) by Ken Hall.
    • KenH
    • Media item
    • bowl segmented spiral
    • Comments: 0
    • Category: Faceplate - 2010 Calendar Contest
  16. mkepke

    Anotehr HF 'Gem': HSS spiral bits

    I've cut 152 @ 3/4"l x1/2"d x1/4" w mortises in walnut with one of these $2.30 center-cutting mortise bits. http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=93450 And can you believe it..that's *after* I used the same bit to grind some cast-iron. The last mortises are not as...
  17. jmauldin

    Byrd spiral cutterhead

    Check out Sunhill Machinery web site. They have the Byrd spiral cutterhead on sale for $149.00. They give a list of machines it will fit, or call them if your machine isn't listed. At this price ALL can afford to upgrade their jointer. Jim in Mayberry
  18. woodnick

    Spiral vs Helical

    Does any one have experience using both Spiral and Helical cutter heads. I'm going to change the cutters on my jointer and would like to know which would be best to change to. I will be cutting mostly Pine.
  19. cskipper

    Spiral blade question

    I have a little (read very little) shop time over the weekend, so I though I'd practice using spiral blades. I have 2/0 FD "new" spirals. I'm getting the hang of using them, but they leave extremely rough inside edges (vertical lines). It seems that it will take forever to sand in addition to...
  20. Tarhead

    CLT CL: Grizzly 8" Jointer w/ Spiral Cutterhead

    Not mine: http://charlotte.craigslist.org/tls/525049452.html (It's calling your name Jeremy)

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top