64a

  1. Motor Access Hole Template

    Motor Access Hole Template

    The age-old tradition of trial-and-error was used to determine size and location of the motor access hole. The template was used to route the hole.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  2. Setup for Cutting the Miter Slots.

    Setup for Cutting the Miter Slots.

    This picture was taken after-the-fact, so you need to use your imagination to understand how this works. Install the table on temporary riser blocks (this is necessary to allow clearance for the router bit between the table saw and extension table). Temporarily place the Aluminum T-Track in...
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  3. Miter Gauge Template

    Miter Gauge Template

    Location of the two T-slot Aluminum Miter gauge tracks must be dead on. The gap between the miter bar and the track is 0.005" on either side. The template was made for use with a top-bearing 1/4' height template bit.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  4. Motor Access Hole

    Motor Access Hole

    Table saw blade fully retracted, tilted to 45 degrees.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  5. Table Support Detail

    Table Support Detail

    Angle iron attached to mounting block with 1/4'' bolt and T-nut. Mounting blocks are screwed, and glued, to table. Top is 5/8'' particle board covered with laminate. Underside of table is reinforced with 5/8'' x 1-1/2'' particle board.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  6. Angle Iron Table Mount

    Angle Iron Table Mount

    1-1/4'' x 3/16'' heavy-duty angle iron table support. Short pieces of angle iron are used to attach the table support to existing holes in the table saw. Note shims (washers) between angle iron and table top assembly.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  7. Motor

    Motor

    Closeup of motor in table top clearance hole.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  8. Adjustable Foot.

    Adjustable Foot.

    Coaster required on sloped floor.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  9. Adjustable Foot.

    Adjustable Foot.

    Whoops! Had to add small wooden disk to increase height of foot.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  10. Fold-up Table Leg

    Fold-up Table Leg

    Shown folded up position.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  11. Fold-up Table Leg

    Fold-up Table Leg

    Shown folded down with leg locked. Knob is inexpensive lawn mower handle-replacement from Borg. Carriage bolt is 5/16'' x 4''L.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  12. PowerMatic 64A Fold-Up Outfeed Table

    PowerMatic 64A Fold-Up Outfeed Table

    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  13. PowerMatic 64A Outfeed Table

    PowerMatic 64A Outfeed Table

    PowerMatic 64A Aircraft Carrier.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  14. Outfeed Table Raised

    Outfeed Table Raised

    Full table dimension in folded-up position is 46-1/2'' deep x 52-1/2'' wide.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  15. Outfeed Table Folded Down

    Outfeed Table Folded Down

    The small permanently attached table is 12-1/2''D x 52-1/2''W, large fold-up table is 32-1/2''D x 52-1/2''W.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  16. Motor

    Motor

    Motor shown with blade down, tilted to 45 degrees.
    • KC7CN
    • Media item
    • 64a fold-up outfeed powermatic table tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Outfeed Table
  17. PM64A Extension Table

    PM64A Extension Table

    Oak framed laminated table extension.
    • KC7CN
    • Media item
    • 64a extension pm64a powermatic table
    • Comments: 0
    • Album: PowerMatic 64A Table Saw - Shop Made Accessories
  18. Rear Drawer Hangers

    Rear Drawer Hangers

    • KC7CN
    • Media item
    • 64a drawer powermatic saw table tool
    • Comments: 0
    • Album: PowerMatic 64A Table Saw - Shop Made Accessories
  19. Open Drawer

    Open Drawer

    WOOD Magazine December 2001, Issue 138, Shop Tips, Page 40.
    • KC7CN
    • Media item
    • 64a drawer powermatic saw table tool
    • Comments: 0
    • Album: PowerMatic 64A Table Saw - Shop Made Accessories
  20. Side View

    Side View

    WOOD Magazine December 2001, Issue 138, Shop Tips, Page 40.
    • KC7CN
    • Media item
    • 64a drawer powermatic saw table tool
    • Comments: 0
    • Album: PowerMatic 64A Table Saw - Shop Made Accessories

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top