tool
-
Tool tote workshop
- Bill Clemmons
- Media item
- box tool tote workshop
- Comments: 0
- Album: Tote Box Workshop
-
Tool tote workshop
- Bill Clemmons
- Media item
- box tool tote workshop
- Comments: 0
- Album: Tote Box Workshop
-
Tool tote workshop
- Bill Clemmons
- Media item
- box tool tote workshop
- Comments: 0
- Album: Tote Box Workshop
-
Tool tote workshop
- Bill Clemmons
- Media item
- box tool tote workshop
- Comments: 0
- Album: Tote Box Workshop
-
Tool tote workshop
- Bill Clemmons
- Media item
- box tool tote workshop
- Comments: 0
- Album: Tote Box Workshop
-
Tool tote workshop
- Bill Clemmons
- Media item
- box tool tote workshop
- Comments: 0
- Album: Tote Box Workshop
-
Tool tote workshop
- Bill Clemmons
- Media item
- box tool tote workshop
- Comments: 0
- Album: Tote Box Workshop
-
Tool tote workshop
- Bill Clemmons
- Media item
- box tool tote workshop
- Comments: 0
- Album: Tote Box Workshop
-
Tool storage chest
Chest of drawers for chisel and bit storage. There is a lift-out rack to hold Forstner bits in order.- Charlie Buchanan
- Media item
- bit case offcut project storage tool
- Comments: 0
- Category: Member Galleries
-
Tool storage chest
Chest of drawers for chisel and bit storage. Built it out of scraps left over from other projects. It is a walnut veneer plywood case with face frame. Drawers are traditional drawer box construction with web frames suspension.- Charlie Buchanan
- Media item
- bit case offcut project storage tool
- Comments: 0
- Category: Member Galleries
-
Tool storage chest
Chest of drawers for chisel and bit storage. Built it out of scraps left over from other projects. It is a walnut veneer plywood case with face frame. Drawers are traditional drawer box construction with web frames suspension. Knobs are turned from furniture leg offcuts.- Charlie Buchanan
- Media item
- bit case offcut project storage tool
- Comments: 0
- Category: Member Galleries
-
miter paring jig
I made the guide to fit 3/4 stock with a centered 1/4 inch wide panel groove. The guide has a tongue that rides in the groove and can be clamped in vise to hold it securely for paring the miter. In this illustration the inner groove wall of the rail will not be mitered so the tenon shoulder is...- Charlie Buchanan
- Media item
- guide hand jig paring tool
- Comments: 0
- Category: Smaller Woodworking Projects
-
miter paring jig
Miter paring guide shown where it mates with the rail or stile to be mitered.- Charlie Buchanan
- Media item
- guide hand jig paring tool
- Comments: 0
- Category: Smaller Woodworking Projects
-
miter paring jig
Photos show a small paring guide for mitering the moulding on frame and panel door stiles and rails. I made the guide to fit 3/4 stock with a centered 1/4 inch wide panel groove. The guide has a tongue that rides in the groove and can be clamped in vise to hold it securely for paring the miter.- Charlie Buchanan
- Media item
- guide hand jig paring tool
- Comments: 0
- Category: Smaller Woodworking Projects
-
miter paring jig
Miter paring guide set up to pare the outer molding. Normally the unit would be gripped in a vise to hold it steady.- Charlie Buchanan
- Media item
- guide hand jig paring tool
- Comments: 0
- Category: Smaller Woodworking Projects
-
panel raiser plane reprofile
top showing the skew.- Charlie Buchanan
- Media item
- panel plane project raiser tool
- Comments: 0
- Category: Member Galleries
-
panel raiser plane reprofile
Side view of the plane- Charlie Buchanan
- Media item
- panel plane project raiser tool
- Comments: 0
- Category: Member Galleries
-
panel raiser plane reprofile
Old profile produced a concave rounding of the panel. I wanted a more traditional straight bevel to a flat tongue.- Charlie Buchanan
- Media item
- panel plane project raiser tool
- Comments: 0
- Category: Member Galleries
-
panel raiser plane reprofile
Reprofiled panel raiser plane sole.- Charlie Buchanan
- Media item
- panel plane project raiser tool
- Comments: 0
- Category: Member Galleries
-
panel raiser plane reprofile
I planed the sole to the new profile. Then marked the iron with the new profile and reground the shape of the edge to match.- Charlie Buchanan
- Media item
- panel plane project raiser tool
- Comments: 0
- Category: Member Galleries