bottom

  1. Top and Bottom plates glued and rough shaped

    Top and Bottom plates glued and rough shaped

    • MikeH
    • Media item
    • and bottom glued plates rough shaped top
    • Comments: 0
    • Album: Mandolin Build
  2. bad bottom

    bad bottom

    bad bottom
    • erasmussen
    • Media item
    • bad bottom
    • Comments: 0
    • Album: other
  3. Bee Bottom Board

    Bee Bottom Board

    Bee Bottom Board
    • sash plane
    • Media item
    • bee board bottom
    • Comments: 0
    • Album: Form Photos
  4. Bocote Bowl reversed

    Bocote Bowl reversed

    This is the same bowl when turned upside down.
    • woodturnerdon
    • Media item
    • bocote bottom bowl
    • Comments: 0
    • Category: Turning Projects
  5. Mike Davis

    What does the bottom look like?

    I have been told I need to do my bowls a little differently. But, I haven't seen many wood bowls and so I'm not sure what people do to the bottom. After it is all done and you put it back on the lathe what do you do to the bottom to make it more finished looking? I have been leaving the...
  6. Sapwood_Bottom_002

    Sapwood_Bottom_002

    • Gunslinger
    • Media item
    • bottom sap
    • Comments: 0
    • Category: Member Galleries
  7. Sapwood_Bottom_001

    Sapwood_Bottom_001

    • Gunslinger
    • Media item
    • bottom sap
    • Comments: 0
    • Category: Member Galleries
  8. seed pot wip

    seed pot wip

    border diamonds
    • erasmussen
    • Media item
    • border bottom diamond pot seed
    • Comments: 0
    • Album: turnings
  9. seedpot bottom

    seedpot bottom

    seedpot bottom turning
    • erasmussen
    • Media item
    • bottom seedpot
    • Comments: 0
    • Album: turnings
  10. bottom of turning

    bottom of turning

    • erasmussen
    • Media item
    • bottom large open segment turning
    • Comments: 0
    • Album: turnings
  11. Shamrock

    Roubo Bench-The top and the bottom meet!-Finally

    Well, it was bound to happen sooner or LATER, I'm finally starting to make good progress on this puppy. After the last post(where I actually glued up the bottom section-the base) I had to place it on the top to mark out the location of the BIG mortises: After that I drilled them out with a...
  12. KC7CN

    Finger-joint Box - Help with Top & Bottom

    This is one of those "just for something to do" projects. I made some improvements to my finger-joint jig and made this box to test it. The dimensions are 11"W x 11"D x 4-3/4"H. The stock is 3/8" - I think it's Alder. The finger joints look okay, so I glued up the four sides to make a box...
  13. ErnieM

    Harpsichord Project Part 5 - Case Bottom

    Hi all, The type of instrument we are building requires the case sides to sit ON TOP of the case bottom so the next component we need to build is the Bottom of the case. It would be easier to build the Bottom out of ½” plywood but, for tonal reasons, we can’t. Instead, we will build the Bottom...
  14. toolman

    [Other-Main Site] [Other-Main Site] number hot links at bottom of page??

    Down at the bottom of the page there is a row of numbers 1 thru 90. they are hot links to the site pages, number 36 is below: Just letting you know! North Carolina Woodworker > Woodworking > Wood <hr> PDA View Full Version : Wood <hr> Pages : [1] 2 <hr> ID help? Never know what you...
    • toolman
    • Thread
    • bottom hot links number othermain page
    • Replies: 1
    • Forum: Help Desk
  15. owen299

    Nice Smooth Bottom / Longworth chuck

    I found some directions online for a longworth chuck. Seemed fairly simple to make , and only cost a few dollars at Ace Hardware for some bolts wingnuts and stoppers. nothing like a nice smooth bottom:gar-La;
    • owen299
    • Thread
    • bottom chuck longworth nice smooth
    • Replies: 5
    • Forum: Woodturning
  16. L

    Cabinet drawer bottom question

    I have a question concerning the 1/4 inch plywood that usually goes in the bottom of a drawer. These drawers are on slides and go into a pantry cabinet that is 23" deep by 18" across. Is 1/4 " heavy enough for pantry bottoms? Lorraine
  17. H

    ShokeShaves....Flat bottom and Round Bottom?

    I recently picked up a near mint Stanley #151 spokeshave with the flat bottom and it does a fine job. Seeing as I'm not too familiar with spokeshaves, I was wondering if there's a spokeshave with a rounded, concave bottom for working on rounded stock such as hickory axe handle or spokes:-D I'd...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top