twisted

N
My fence is twisted...

I know that this is not new news in regards to the Ridgid fence, but should I worry about this?... I'm not talking about 90 deg to the blade/miter slots, I'm talking about vertical fence-to-table. It's square at the front along the length of the table and the back remains .25 of a deg. off...
- NH2NC
- Thread
- Nov 9, 2010
- fence ridgid fence twisted
- Replies: 4
- Forum: Power Tools and Their Use
G
Warped or Twisted

I am fairly new to woodworking and this site. This site is a great resource, and I enjoy it immensely. I have a question: I purchased some 8 qtr Sapele to make a desk, and I am taking it down to about 1 5/8. One piece (out of seven) is seriously warped or perhaps twisted. But when i clamp it...
- Grey
- Thread
- Feb 15, 2009
- twisted warped
- Replies: 2
- Forum: "How To" Forum
D
Twisted wood

Here's some pics of a couple of my "twisted" workings. http://www.ncwoodworker.net/pp/showphoto.php?photo=29455&ppuser=3075 http://www.ncwoodworker.net/pp/showphoto.php?photo=29456&ppuser=3075 http://www.ncwoodworker.net/pp/showphoto.php?photo=29457&ppuser=3075
- Dragon
- Thread
- Dec 20, 2008
- twisted wood
- Replies: 3
- Forum: General Woodworking
Gate Latch

Gate latch on twisted post
- KC7CN
- Media item
- Sep 4, 2007
- cedar fence gate latch posts twisted
- Comments: 0
- Album: Cedar Fence
Close Up

Birds eye view of end post.
- KC7CN
- Media item
- Sep 4, 2007
- cedar fence post twisted
- Comments: 0
- Album: Cedar Fence
Twisted Post - West Side

End post against block retaining wall.
- KC7CN
- Media item
- Sep 4, 2007
- cedar fence post twisted
- Comments: 0
- Album: Cedar Fence
Fence Hanger

Close up of fence hanger on twisted post.
- KC7CN
- Media item
- Sep 4, 2007
- cedar fence post twisted
- Comments: 0
- Album: Cedar Fence
Twisted Post - East Side

This post is about 7' above ground.
- KC7CN
- Media item
- Sep 4, 2007
- cedar fence post twisted
- Comments: 0
- Album: Cedar Fence
L
twisted / warped wood

I have gotten some engilsh walnut that was not properly stacked while drying. It has a great color and grain, but I have had to cut most in strips about 2" wide to get some short pieces for small projects.I wanted to make a display cabinet for my wife but a little baffled with what to do. I have...
- lhmayberry
- Thread
- May 15, 2007
- twisted warped wood
- Replies: 23
- Forum: General Woodworking
Twisted inset doors -FIXED

I just mounted the doors in the lower cab of my kitchen hutch. They have a slight twist to them, about a 1/8". They are inset, flat panel doors with two panels per door. Other than remaking them, which I have already done once :BangHead: :BangHead: any suggestions as how to either take out the...
- DaveO
- Thread
- Jan 4, 2007
- doors fixed inset twisted
- Replies: 21
- Forum: General Woodworking
Twisted hiking stick

I have some chestnut that I would like to use to make a hiking stick. I have one, a gift, that has a "twisted" appearance and I think I'd like to do that. Here is a web site with pics of what I'm talking about...
- smessick
- Thread
- Nov 8, 2006
- hiking stick twisted
- Replies: 19
- Forum: General Woodworking