insert

  1. Riving Knife & ZC Insert

    Riving Knife & ZC Insert

    Shop made riving knife and zero clearance insert.
    • KC7CN
    • Media item
    • 64a clearance insert knife powermatic riving shop-made zero
    • Comments: 0
    • Album: PowerMatic 64A Riving Knife
  2. cyclopentadiene

    Router Table Insert Problem

    I was using my router table yesterday and had a very scary incident. I had a 2" pattern cutting bit in the router trimming a chair leg to the pattern when two of the screws holding the router to the router plate tore loose. I quickly unplugged the router. I purchased the Benchdog clear...
  3. Joe Scharle

    Bandsaw table insert, step by step

    Had a cutoff jam in the insert yesterday and it caused a permanent pucker at the mouth that won't go flush with the table. RIDGID says my new one will be here in 10-14 days, so this AM I made one from 1/4" hardboard and thought I'd go back, take some pics and share this. First, as with any...
  4. N

    45-degree zero clearance insert

    Anyone have a good way to cut a 45-degree kerf in a left-tilt table saw zero clearance insert? I can't retract the blade far enough for the insert to fit in the throat at all; it just rocks on top of the blade. I tried resting it on a couple of thin slats laid at right angles across the throat...
  5. J

    router table insert

    I am looking for a deal on a router table insert for a Freud FT2000E 3-1/4 hp router. If I dont find a good deal, I have enought 1/4" plexi-glass to mess up 4 or 5 times learning to make one. James
  6. J

    Insert SketchUp into Thread

    How do I do this? I tried it awhile back, but got an error message stating that it wasn't supported (couldn't be done). I've seen a few recent threads that have SU in them. Thanks.
    • Jeff
    • Thread
    • insert sketchup thread
    • Replies: 5
    • Forum: Help Desk
  7. R

    Router Table Insert

    Can someone recomend a good router table insert, I am building a router table and want something that wont sag. I have no experience with this so any help would be appreciated. Thanks!
  8. R

    zero clearance insert for Rigid TS 3612 table saw

    Does anyone know where I can find a zero clearance insert for my Rigid TS3612 table saw? When I originally bought my zero clearance insert, it was an AC1035. It shattered a few days ago for no reason that I can see, except that it must have been vibrating during use. Now, though, the only...
  9. rick7938

    Thoughts on Router Table Insert

    I am getting ready to build a new router table. I have bought a new insert for my P-C 690 router. Since I don't do any heavy routing the 690 is all I need. However, I just read a couple of books by Pat Warner who does not favor an insert, but screws his routers directly to the table top. Since...
  10. ZCI for Table Saw

    ZCI for Table Saw

    • Wilmingtonian
    • Media item
    • bt3100 clearance insert zci zero
    • Comments: 0
    • Album: Tools
  11. ZCI for Table Saw

    ZCI for Table Saw

    • Wilmingtonian
    • Media item
    • bt3100 clearance insert zci zero
    • Comments: 0
    • Album: Tools
  12. ZCI for Table saw

    ZCI for Table saw

    I got the idea from http://benchmark.20m.com/tools/BT3100/BT3100_ZCI/BT3100_ZCI.html. It is made from baltic birch ply.
    • Wilmingtonian
    • Media item
    • bt3100 clearance insert zci zero
    • Comments: 0
    • Album: Tools
  13. Tarhead

    Disable Automatic Abbreviation Complete, Smiley Insert Function?

    Tried to use TS-55 (Festool's model number for their circular saw which plunges 55mm, T-S-55 not a Table Saw) and the auto-complete function inserts Table Saw. Can this and the auto smiley insert function be disabled? Thanks!
    • Tarhead
    • Thread
    • abbreviation automatic complete disable function insert smiley
    • Replies: 6
    • Forum: Help Desk
  14. Mark Gottesman

    Zero Clearance insert for 1950's Craftsman TS

    I need to make some ZCI for my Craftsman "100" TS. It has the original throat plate which is a piece of 3/32" thick aluminum. so it is thin and is prone to bending. Not an ideal material. There are new after-market ones available for about $25.00 apiece, but that seems expensive if I want a...
  15. L

    Threaded insert question

    They say there is no stupid question so here goes. I am attaching the top of a display cabinet to the bottom section. I have four threaded inserts that I have placed in the bottom of the top section aligned over four holes that were drilled into the top of the bottom cabinet. This is a...
  16. Truefire

    Cedar barrel duck call with bloodwood insert

    Thought you guys might enjoy looking at my recently finished double reed duck call. I used cedar for the barrel and bloodwood for the insert and cut my own reeds. Needs a couple more coats of finish however.
    • Truefire
    • Thread
    • barrel bloodwood call cedar duck insert
    • Replies: 6
    • Forum: Woodturning
  17. Zero Clearance Insert - 4

    Zero Clearance Insert - 4

    Additional inserts
    • eddie joe
    • Media item
    • clearance insert zero
    • Comments: 0
    • Category: Member Galleries
  18. Zero Clearance Insert - 3

    Zero Clearance Insert - 3

    Bottom bracing and adjustment screws
    • eddie joe
    • Media item
    • clearance insert zero
    • Comments: 0
    • Category: Member Galleries
  19. Zero clearance insert - 2

    Zero clearance insert - 2

    Sliding dovetail, 45 degrees
    • eddie joe
    • Media item
    • clearance insert zero
    • Comments: 0
    • Category: Member Galleries
  20. Zero Clearance Insert - 1

    Zero Clearance Insert - 1

    Installed in saw; zero clearance inserts can be made out of wood. This is one I have been using for years. It is made out of 1/4 in plywood and hardboard. The insert is cut at a 45 degree angle like a dovetail. See attached pictures with captions. The bracing on the bottom is half-inch...
    • eddie joe
    • Media item
    • clearance insert zero
    • Comments: 0
    • Category: Member Galleries

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top