trim

  1. C

    Looking for custom egg-and-dart trim for mantel

    Hello! I would dearly love to find someone within an hour or so of Cary to carve about 10 feet of egg-and-dart for our dining room mantel. The two "legs" would be 40" to the corner from the base and the horizontal piece would be 44" long to the corners, with an acanthus leaf at the two corners...
  2. C

    Trim The Tree Contest

    Please check the calendar for complete information regarding the Trim The Tree Contest that The Hardwood Store of NC, Inc. is having. Thanks. Cheryl The Hardwood Store of NC, Inc.
  3. Barbie House Dresser Drawers - WIP

    Barbie House Dresser Drawers - WIP

    Barbie House Dresser Drawers and Trim Stained and Glued
    • MarvinWatkins
    • Media item
    • and barbie drawers dresser glued house stained trim
    • Comments: 0
    • Category: Member Galleries
  4. kooshball

    Which plane or plane setup is best to trim tails and pins on through dovetails?

    I finished the top box for my dovetailed bookcase out of rswo and now need to trim the excess tail and pin material. Which plane is going to give me the best results on the end grain of this hard lumber? I have a jack plane, a fore plane and a low angle block plane at my disposal... Thanks
  5. CDPeters

    Need some advice - exterior trim

    Folks - I need some help. LOML and I are replacing the columns and railings on our front porch. We have selected a metal railing but want to keep the turned post style we have. Neither of us is getting any younger and we would like to do something that will not require frequent maintenance...
  6. AmishWarlord

    Trim work

    Trim work is nice so why limit it to the edge molding? I say Trim everything! LOL, just kidding.
  7. zapdafish

    window trim question

    I would like to do some craftsman trim around alot of my windows. I have looked at videos and browsed alot of books and they all seem to start with the window frame exposed as a starting point. Below is a pic of one of my windows. I can tell the sill and sides are plastic but based on my stud...
  8. BKind2Anmls

    HF Trim Router - $20

    I bought a couple of these several years back and I keep one loaded with a round-over bit and one loaded with a chamfer bit. It is really handy to have them ready at a minute's notice to quickly route a slight round-over or chamfer.
  9. C

    Oak Trim

    Where can I find some Oak trim? I am working on a cabinet and was looking for some accent trim in Oak to purchase. The alternative is to make it with a router but I only need a few pieces. I am looking for somewhere in Raleigh. Chris
  10. W

    Flexible trim molding

    Per request from the Mrs, I am looking to put some flexible trim molding in an area in our master bedroom. Need some insight into where I can find some flexible molding locally and the approx cost? I do not recall seeing this at the local HD or Lowes. Any insight on where I can buy this and...
  11. Canuck

    Trim Saw Blades?

    I have a handy corded older Skil trim saw that take a 5 1/2" blade - 5/8" - 1/2" arbor. I am looking for a new blade that is usable on plywood. I recently found a Freud 40 tooth (I think) blade for my 7 1/4" circ saw and would like something similar for the smaller trim saw but am having a lot...
  12. S

    trim shaping problem

    I am trying to figure out how to match some trim for a piece I'm working on. I need 25' of OAK 3/4 X 1 1/2 with a 3/4" bull nose type curve on each side. I could just use a bull nose router bit, but it would leave a flat spot between curves. I could also cut a bull nose on each piece, rip it to...
  13. BriarJim

    Looking for enthusiastic trim carpenter/cabinet installer

    If you live in or near the Triangle area, I could use your help. I am a business start-up called Quintessentially Designed, Inc. All details will be discussed based on responses, but bottom line is I want to work with someone who can help or do installations, estimates, designing and building...
  14. Router table with new fence and edge trim on the top

    Router table with new fence and edge trim on the top

    In this step, the edge trim is complete and the fence is done as well
    • merrill77
    • Media item
    • edge fence router table trim
    • Comments: 0
    • Category: Member Galleries
  15. Applying edge trim to router table top

    Applying edge trim to router table top

    • merrill77
    • Media item
    • biscuit edge router table trim
    • Comments: 0
    • Category: Member Galleries
  16. VZ trim

    VZ trim

    • Henry W
    • Media item
    • home renovation trim
    • Comments: 0
    • Album: Home renovation
  17. VZ trim

    VZ trim

    • Henry W
    • Media item
    • home renovation trim
    • Comments: 0
    • Album: Home renovation
  18. Door trim with rosettes

    Door trim with rosettes

    • merrill77
    • Media item
    • door rosette trim
    • Comments: 0
    • Category: Member Galleries
  19. H

    Trim carpentry choices?

    All: A friend has asked me to finish up the trim work in his bonus room - work he is simply not getting to. Without regular FT work, I am jumping at the option. I have questions though. The homeowner is fine with whatever I choose. The end walls have bump-outs where the HVAC ducts are housed...
  20. S

    PC Lam Trim Router-$64 Amazon

    Not Refurb-Brand New, Should qualify for free SuperSaving Ship! http://www.amazon.com/Porter-Cable-7310-4-Horsepower-Laminate-Router/dp/B0000222Z6/ref=pd_rhf_p_t_2

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top