time

  1. Leviblue

    I needed some shop time

    I haven't been able to spend much time in the shop lately, but today I was able to get out and take a break from the hurricane effects we are having here. I had a Zen kit sitting around for a while and was thinking about what type of wood to put with it. I found some ambrosia maple in a section...
  2. TracyP

    May be Moderation Time

    http://www.ncwoodworker.net/forums/showthread.php?t=40521 Ethan is posting a response as I type this. We should watch this one closely.
  3. J

    Long Time Lurker...

    ...First Time Poster Hi I'm Joe. I moved to Cary a little over a year ago with my wife and 3 kids (2 boys 6&4, 1 girl 2). Now that my daughter is a little older and my wife is getting more sleep I am hoping to get back to real woodworking. Most of my woodworking over the past few years has...
  4. 4barnwood

    First time with my Chainsaw Mill.

    Finally got something made with my Chainsaw Mill. I used an Oak log that was damaged in a storm and Reclaimed Barn Wood for the frame. Its alot smoother than it looks. The saw marks turned out cool. I donated it to a local elementary school for a silent auction they are having.
  5. W

    First time turning questions

    Ok, so I got my lathe set up (thanks Jay) and started messing around just a little bit with scraps of wood, nothing serious. I turned a fresh piece of Box Elder that I picked up after a large limb broke off a tree in town the other night. I didn't have any design in mind, just getting a feel for...
  6. L

    Do belt sander belts go bad over time?

    In an earlier post, I mentioned that I am finally back in action from a woodworking standpoint after a three and a half year absence due to living in a rental property. Now that we have our own home again I am busy making replacement cabinets. I had a lot of 3" x 18" belts left which had now...
  7. LeftyTom

    I Need Some Time on a Belt Sander

    I need to sand a 36" L x 27" W x 2" T edge grain butcher block top. (Yes, I finally got the sections glued together.) The top is made out of white oak I bought from Rick DiNardo at The Woodworking Source. I am 30 minutes from Wilkesboro, Statesville, Mocksville, and Winston-Salem; an hour...
  8. cskipper

    Time to document procedures?

    Now that we are entering another year, I think it may be time to get some written procedures in place. This will help with continuity as the board transitions, and especially if someone leaves the board mid-term. The info below is not intended to be a complete list, but just a starting point...
  9. Gotcha6

    Good Will Lathe Time

    It's time again to move the Good Will Lathe to a new home. Nominations for recipients will be considered until August 1. A selection will then be made afterwards and recipient will be responsible for picking up the lathe from its current holder, mburke911 in Cary.
  10. MarkE

    So, anyone planning a trip to Connecticut any time soon?

    I know this is a real big long shot, but I had to ask. Found a table saw for sale in Tolland, but I can't come up with a way to get enough time to go up there and get it. A pickup truck and of course gas money can be provided. :gar-Bi
  11. Bill Clemmons

    Lunch time in the Triad

    I think it's about time for another group lunch in Greensboro; how about you? How does next Thursday, the 21st sound? Same time; same place: 11:30, The Moose Cafe at the Farmer's Market. Exit 208 off of I-40. See ya there. Come one, come all. Bill
  12. manfre

    PM time delay

    Any chance that the time delay between sending PMs (or at least PM replies) can be reduced from 60 seconds to 30. I routinely am stuck sitting with open browser tabs with written messages, but am forced to wait between sending. I realize that the time based throttling helps prevent spam, but it...
  13. dlrion

    Goldsboro Lunch! One last time!

    Guys I am sorry I kinda let the shop crawl get away from me, I got orders to California and I have been flying all over the country learning how to do my new job. I got back two weeks ago. I would really like to have one last lunch with you guys but I will be in Nevada for a week this month...
  14. Bill Clemmons

    Greensboro Lunch Bunch Time

    It's about time for another lunch in Greensboro. How about Thursday, June 23, at The Moose Cafe. 11:30 usually works for everybody. That's more than two weeks out, so plenty of time to arrange schedules. :gar-Bi If you live in the area, or just passing through, we'd love to have you join our...
  15. L

    Need to sign in each time I come back

    Has something changed? When I exit the site and return I have to sign in each time. How can I change this?
  16. kooshball

    Good time to upgrade the whole TS fence vs just getting long rails?

    I have the G1023Z saw with the 25" rail Shop Fox Fence listed below: http://www.grizzly.com/outlet/Fence-w-Standard-Rails/G4722 I currently don't have issues with parallelism but just don't have enough rip capacity and have ordered the 49" rip length rails. Unfortunately, the rails arrived...
  17. M

    Teaser Time!

    In less than a week, we will announce the Spring North Carolina Woodworker Raffle! I'm proud to say that we have our largest suite of prizes ever -- over $4,500 worth! We've got everything from marking and layout tools, to top quality hand tools for prepping your joinery, to major power tools...
  18. WoodenU

    Play Time......

    Many years ago I had made a marble board just for the heck of it, as it turned out we have been playing on that same board very frequently, some times several times a week, my 82 year old mother in-law just loves the game. Some people call the game aggravation, wa-hoo and a few more... we just...
  19. ScottM

    GWL - Good Will Lathe Time

    Well folks Steven (Zapafish) is ready to pass the good will lathe on the next lucky person. For the newer folks the GWL was a donation made by our founder Steve Coles. It is a Rikon lathe, complete set of turning tools, grinder, wolverine sharpen jig, a chuck, live center, and other...
  20. DWSmith

    That Time of the Year

    In February and March, Lowe's will be marking down their slow sellers and tools that will be replaced by newer models. If you are looking at something and want a discount, this is the time to keep your eyes open. Also, this happens in all departments in the store. The key to knowing what is...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top