tablesaw

  1. G

    Also received a G0690 tablesaw

    While I was getting the new jointer, I also had Grizzly throw in a new tablesaw. Thought you folks would to know the story behind it as well. When I went to work again for the Department of Defense I had to sell my beloved unisaw. My wife said it got better rub downs with paste wax every...
  2. 6

    Tablesaw going to sale, have a question.

    Tis a cold day. So I have to liquidate some equipment due to lack of work area. First thing that has to go is my cabinet saw. Its a Sawstop 3hp cabinet with all the extra's. I've never seen one for sale locally, in the classifieds or really anywhere else other than brand new. Is there no market...
  3. froglips

    Raleigh CL: 12" 3hp 220V Cabinet Saw and Dust Collect $400

    Uhm, is this a deal or what? Jim http://raleigh.craigslist.org/tls/1209199708.html Heavy duty 12 inch blade table/cabinet saw (cut a 4x4 in 1 pass) with 42" cut 3 HP 220v mower, enough power to rip a damp pressure treated 4x4 includes 5 carbide tip blades and 4 steal blades...
  4. redhawknc1

    My New To Me Tablesaw Gloat....Thanks to North Carolina Woodworker!

    Finally got my "new to me" Jet 10" 3hp Xacta saw together and tuned. Used my rails and Beismeyer Fence from my old Delta Contractor Saw(Lowes deal from a while back). Along with the Incra 1000SE and Bench Dog Cast Iron Router Table Extension. Have a PC7518 and Bench Dog Pro Lift mounted...
  5. Outa Square

    Bandsaw only shop - no tablesaw

    I haven't been working on building my shop slowly since last November. I now have a floor and two walls waiting to be set in place. The deal i made with my wife and myself is that the money that i have left over from my alloted budget i can spend on tools; needless to say that i am doing good...
  6. Bryan S

    A Tablesaw Reminder.

    I know it gets put here fairly regular but wanted to remind everyone again about care with the tablesaw. One of the operating room nurses told us last night there were 2 people brought into Cone Hospital with injuries from tablesaws both required surgery. I don't know anything about either of...
  7. Ken Massingale

    Delta-Obi Tablesaw???

    Delta Tablesaw 10" - $325 (Greenville, SC) This guy can't even read the Ryobi label on his saw!:no: http://greenville.craigslist.org/tls/1131163352.html
  8. Tarhead

    Tablesaw Top Allignment

    I was whining to the Forrest Blade rep at the Charlotte WoodWorking Show yesterday about the performance of my WWII Thin Kerf Blade and problems with burning during miter cuts and crosscuts. He asked me about how have I alligned my tablesaw top and I responded that I've never quite got a round...
  9. Small Parts Miter-Gauge Clamp

    Small Parts Miter-Gauge Clamp

    From Woodsmith Tips. Handy jig for holding small parts. Modified to include T-Slot for attaching to miter-gauge. Opposite end of Jaws adjusted to width of the small part. http://woodworkingtips.com/etips/2009/02/12/sn/print
    • KC7CN
    • Media item
    • clamp jig miter-gauge parts small tablesaw
    • Comments: 0
    • Album: PowerMatic 64A Table Saw - Shop Made Accessories
  10. A

    Quick Tablesaw measurement needed?

    I need some data about the distance between your arbor flange (not the bolt flange washer) and the inside edge of the facing miter slot. Could you all please provide this info with saw make/model and distance. If you don't want to remove your blade just give me the distance to the flange side...
  11. F

    CLT CL: tablesaw, jointer, bandsaw

    http://charlotte.craigslist.org/tls/1043736071.html Oldies but goodies.
  12. Tablesaw Safety Gear

    Tablesaw Safety Gear

    Board Buddies, Feather Board, Push Sticks, Outfeed Table
    • McRabbet
    • Media item
    • safety tablesaw
    • Comments: 0
    • Album: My Shop
  13. rcflyer23

    Tablesaw

    I need some recomendations the current saw I have fell over and broke a couple of the mounts and since it is plastic there isn't really any good way to fix the mounts that I know of. I knew one was broke so I tightned the others but today I found out the other one was broke when I was pushing...
  14. NCTurner

    Jointing on a tablesaw

    Anyone ever do any jointing on a tablesaw? I have been stocking my shop and WG funds aren't there for a jointer right now. I have been thinking about starting with a jig like this Jointing Jig. Figured it could get me by until funds are free'd up.
  15. Travis Porter

    The ultimate tablesaw

    Yes, I said ultimate tablesaw only because I have seen one of these up close and in person. It is a true precision instrument. What a machine for only $31,000!!!! Yes, that is THIRTY-ONE THOUSAND DOLLARS. WAY OUT of my price range, but I am thinking it would be just right for Bernhard or...
  16. DaveO

    Negative hook blades on tablesaw???

    Are there any issues with using a negative hook blade on a TS. I know the benefits of using them on a RAS or SCMS, but would those benefits be liabilities on a TS???? Just a question I've been pondering over and I thought I would see what the NCWW brain-trust had to say about it :icon_thum Dave:-)
  17. zapdafish

    tablesaw disk sander

    Anyone use one of these? I am going to try making a curved template for my router this coming weekend and since I don't have a sander, I thought I would give it a try rather than do it by hand with a sanding block. Not sure if the tablesaw might be to fast, etc. Thnx...
  18. DaveO

    Tablesaw ZCI...

    I am in the need for a few new ZCI for my Griz saw (0444Z) to deal with the new full kerf blades I have coming. I know that I can make them myself, and have tried that. But I have never had much success with installing top mounted leveling screws. I have been using the ZCI that Griz offers for...
  19. CarvedTones

    Raleigh CL - a "better than nothing" tablesaw

    http://raleigh.craigslist.org/tls/804941672.html 3HP belt driven - $45 ??? Sounds like it may be in rough condition, though...
  20. L

    Tablesaw measureing tip

    You know when you set the fence on the tablesaw to cut a particular cut and it comes time to make that cut maybe a 3/4" shorter on the next cut? When you move the fence to the left, the placement of the first cut on the tape isn't always an easy measurement to back up from. I have a 6" ruler...

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top