small

  1. merrill77

    Need a small piece of thin cherry ply 12x24

    I need at least 11 1/2 x 22 1/2". I'd prefer 1/4" thick, but could get by with 3/8 or 1/2". Anyone in the Triangle area have a little I can buy or trade for? I'm not going to buy a full sheet for this small bit. Worse comes to worse, I can get by with some BB ply that I have on hand, but if I...
    • merrill77
    • Thread
    • 12x24 cherry piece ply small thin
    • Replies: 6
    • Forum: Wood
  2. erasmussen

    A couple of small turnings

    Not much going on right now but I did get a couple of SMALL turnings out. The first one Paduk, African Blackwood, and mystery wood diamonds. 10" tall 289 pieces the second one 5" tall Cherry Paduk and Bacote 113 pieces and the last one 5" tall Cherry, YH and RH 113 pieces
  3. Truefire

    needing small wooden letters? Can you advise?

    Hey guys, i was wondering if any of you are aware of where i may be able to locate some small wooden letters about 5/16" high or so? various letters of the alphabet? Thanks Chris
  4. danmart77

    Small box -no hinges required

    View image in gallery View image in gallery Here is the same box done with walnut and a second with curly maple left over from a rifle stock. You can see some of the build in danmart77 photos in the photo section. View image in gallery This was a large stump and now its a half stock. dan
  5. N

    Searching for shop to do small production runs (at first)

    I have an idea for a niche furniture product that I'm hoping would grow to volumes that make financial sense. I'm looking to find a shop that would entertain doing short production runs. At first it might be as small as 5-10 pieces a run. The production cost per item is in the range of...
  6. CarvedTones

    Can I sharpen small gouges with this?

    I picked up one of these drill sharpeners used on CL. The stop for the bottom of the bit is easily removed. It seems like I could use it to sharpen small turning gouges, like my 3/8" bowl gouge. Any reason that wouldn't work or would be a bad idea? Also, if anyone has one of these and...
  7. jonnyfontaine

    small box

    hello everyone... just wanted to upload a picture of a small figured maple and figured walnut box i made as a wedding gift for my sister in law... but mostly i wanted to show off that spalted maple top, and that i "spalted" the top by collecting various fungi and supplying them with a host...
  8. Mike Camp

    Need two or three small pieces of veneer

    Was wondering if anyone in the Triangle area (closer to Apex the better) had two or three 4" by 4" pieces of veneer I could either have or could pay a small sum for. I'm going to cut them into approx. 3 inch circles on my scroll saw for my son's toy box so around 1/16" thickness or so would work...
  9. CarvedTones

    Grrr-Ripper ordered! (safest way to rip thin strip off small boards)

    UPDATE - OK, you don't have to beat me with a 2x4; well, not that many times... :rotflm: I was swayed by the consensus and the missus even jumped on board for an immediate purchase when she heard it was a safety device that I was making do without. I just got a bunch of spindle blanks that...
  10. froglips

    Milling small box parts from random scrap......

    Whilst working with HOW on making boxes, I think I invented/remembered a neat idea to use up small parts. Short story, Max donated a tone of oak shorts (some as short as 4" long). Great parts for making little boxes....... But, to use box joints and/or router dovetails, we needed some...
  11. ashley_phil

    Small Cabinet Shop in Locust, NC Auction Apr 2

    this isn't my deal. i didn't even know about it until today. could be some good buys depending on the crowd that shows up. http://www.auctionzip.com/cgi-bin/auctionview.cgi?lid=1090770&kwd=&zip=28213&category=0 PUBLIC AUCTION OF WOODWORKING EQUIPMENT & TOOLS SATURDAY, APRIL 2, 9:00 AM...
  12. Carl Fisher

    Can a 10" bandsaw be enough for a small shop?

    I've been seeing the Rikon built craftsman 10" band saw pop up on CL recently. 1/3hp 4 5/8 max cut depth, cast iron table, etc... I'm not expecting to need any serious resaw capacity, but is 1/3hp and 10" enough to grow with or will I be sorry 6-months down the road?
  13. N

    Small Workshop People... How big is too big...

    I have a pretty small workshop (one garage) and I was wondering how big is too big. I'm looking at upgrading my table saw. I'm thinking of making this table saw pretty much the center of my work space. Building a outfeed table that would double as a assembly table and storage at the bottom. So...
  14. erasmussen

    some small turnings

    Today I got around to getting some small turnings, finished (they were almost already finished). Thanks for looking This one is 18" tall This is 10" tall detail And these are just a tiny 6 1/2" tall
  15. sawduster

    small ( ? ) welding job

    A co-workers husband wants to have a safety grill welded across the back window of his Silverado They live in Durham but will travel if neccessary. I do not think they have the material. If anyone is interested in taking this on PM me for contact info. I have no other involvement other than...
  16. MarkE

    Small tool gloat

    Thanks to Travis' (Mt. Gomer) tip here, I ordered this Ridgid 18v drill kit. Ordered on Tuesday, arrived today. :thumbs_up This is a nice kit, Drill, 2 LI batteries with 20 minute charger and a heavy duty carrying bag. HD has this listed with a 3 year warranty but if you register it at...
  17. Rhythm House Drums

    Custom Small Hand Adze with a large sweep

    I'm looking for something similar to this...http://www.rhythmhousedrums.com/images/Tools.jpg The smaller adze up front with the short handle. These by the way are the tools used in West African for hollowing out a wood log to make a drum. My purpose... Stave drums sometimes can have a long...
  18. Small Rocker

    Small Rocker

    1st attempt at a chair - for my granddaughter
    • mark2
    • Media item
    • rocker small
    • Comments: 0
    • Category: Furniture Projects
  19. Cato

    First small table

    Made a small table for our screen porch. I guess this would qualify as my first piece of furniture. Learning curve for me on making a piece of furniture. Learned to laminate the legs, mortise and tenon the skirt, and produce four legs of the same length that sit flat on the floor. Got to use...
  20. T

    Small Box, X-mas gift (FINISHED!!)

    Worked on this on the truck. It is for my brothers girlfriend. The body is oak, the bottom and shelf bottom is 1/8" hardboard and the top is 5/8" mdf veneered bubinga. It is my 1st veneer job. I was at a Woodcraft in Orlando today and he lasered the bottom for me. Need to spray it and line the...
    • toolferone
    • Thread
    • box finished gift small xmas
    • Replies: 22
    • Forum: General Woodworking

Premier Sponsor

Our Sponsors

LATEST FOR SALE LISTINGS

Top