side

  1. 20-IMG_3332

    20-IMG_3332

    Same corner, left side.
    • Tim Sherwood
    • Media item
    • left side view
    • Comments: 0
    • Album: Tim Sherwood Kitchen Remodel NCWW
  2. toolman

    Ads On Right Side?

    We had 8 ads on the right side and now they are gone???? :dontknow:
  3. WorkbenchViews

    WorkbenchViews

    add pass through draws
    • minddust
    • Media item
    • augers for rt side storage
    • Comments: 0
    • Album: Workbench
  4. cyclopentadiene

    Maloof Low Back Side Chair Completed

    I completed my Maloof Low back side chair using walnut and ebony accents as described in the thread Coopered seats in How To forum). Attached are a few photos of the finished product.Overall I am very satisfied with the outcome and look of the finished chair. lesson learned, invest in better...
  5. JCraig

    Side Table for LOML

    My wife had been wanting a table to go beside her recliner for several months. The one she had was way too small for the magazines and books she likes to read. Fortunately, Bill Clemmons was kind enough to give me a few pieces of oak back several months ago, so I decided that this was the...
  6. Shamrock

    Walnut Side Tables Done!

    Finished up these 2 commission side tables yesterday thought I'd snap some pics before they were picked up. View image in gallery I'm happy with the shape, size, and form. Not the happiest with the finish, should have filled the tops before the poly. I did however, manage in the end to get...
  7. PeteM

    Side Tables

    Here's my latest attempt: Walnut base, Maple top with curly redwood Gingko leaf inlay. We have a Gingko tree in out yard and I traced a couple of the leaves for a pattern. I put my new US made Nicholson Rasps to good use on the legs. It was a fun project. I tried out a...
  8. Canuck

    QSRO Side Table

    My youngest daughter was flipping through the pages of a Pottery Barn catalogue and spotted this table. Very plain and she asked if I could build her one on a little smaller scale. I ended up building it out of a combination of flat sawn and quarter sawn red oak from Scott Smith. Overall...
  9. navy1990

    Further descent into the dark side

    After only having my lathe for 2 weeks, I have made 3 rosewood pencils, 3 rosewood pens, a bocote pen, and I have an ebony pen in process (man, that is some hard wood, but it is what my daughter asked for). I may have gotten myself into trouble. I spoke to the head deacon at my church and asked...
  10. Larry Rose

    Wip Side Board

    This is my first attempt at simple marquetry and I've got a newfound appreciation for you guys and gals that do scroling and marquetry. It certainly trys ones patience. This is one of the ends of a side board that wifey wants for our dining room. It's white ash and I'm trying to give it a Green...
  11. Side view air blower on Hegner

    Side view air blower on Hegner

    Side view air blower on Hegner
    • cskipper
    • Media item
    • air blower hegner side view
    • Comments: 0
    • Album: Misc
  12. K

    End grain vs Side grain

    I know this is a simple question for most, but how are the pieces positioned with each option for turning? I just read some thing and just want to confirm, the end grain is where you cut the wood and where the bark is that is the side grain?
  13. C

    Side venting a water heater?

    Another water heater question for you all, sorry :P Anyway, I have a crawlspace with a direct vent water heater that has a vent pipe that goes up a few inches and then horizontal a foot or two through a cinder block wall. It just died and needs a replacement. A friend has an extra water...
  14. DIYGUY

    Another side of WW'ing ...

    This craft has so many aspects to it - here is one that is not often touched on here. Check out the work of this craftsman - truly awe inspiring! http://modelshipbuilder.com/page.php?40
  15. Canuck

    Side Mount Slide ?

    I am relatively new to using drawer slides on my projects.:embarrassed: In preparation for building drawers for a dresser I chose to go with Accuride side mount slides (18"). (It is for my new grand daughter, so I thought that they would be strong, easy to slide the larger drawer in/out and...
  16. M

    Side Chair construction tip

    Upon making some dining room chairs, I was in a dilemma about how to machine the back leg. The back leg and back-rest were cut as one unit on a bandsaw (see photos). I had no problem sanding the kerf-marks on a stationary belt sander, but the joint where the seat attaches became a problem. I...
  17. Shamrock

    Modern Shaker Side Table

    Hey Folks, just thought I'd share some pics of my latest project. This is a little side table I built for my Grandparents 60th wedding anniversary. The plans/design are from Fine Woodworking (July 1989). I'd like to thank Rob (McRabbet) and Greg Smith for helping me locate the plans. I'd also...
  18. sapwood

    See you on the other side

    Well gang, I think it's time. Seems most of the staff is back onboard and Ray is active again :icon_thum At your convenience, Tracy or whomever can take my gun and badge and reactivate me as a regular NCWWer "member". Yeah, I'll miss all the fun on this side, but look forward to enjoying...
  19. merrill77

    Transporting upright compressor on it's side?

    If you were transporting a 60-gal upright compressor, would you lay it on it's side? My trailer has sides that are about 30-in high - so I can strap it into a corner. If I strap my sawhorses to the inside, I'm pretty sure it will stay where I put it. However, I suspect these are pretty...
  20. Bas

    The mechanical side of wiring the workshop

    Work is progressing on the shop, slowly but slowly. After several weeks of taping, mudding and sanding, I've moved to priming and painting. That means less dust but getting the gunk off my hands is now slightly more difficult (paint instead of plaster). :tinysmile_tongue_t: Once the painting is...

Premier Sponsors

Contact for your financial processing needs!

Our Sponsors

LATEST FOR SALE LISTINGS

Top