process

leg volutes

Right side leg spiral decoration. This is about ready to go--or as good as I can get it at this stage.
- Charlie Buchanan
- Media item
- Mar 27, 2016
- chair corner photos process thomas white
- Comments: 0
- Album: Thomas White corner chair
leg volutes

Front leg decorative spirals. This one still needs a little refining to get the bumps down a little lower.
- Charlie Buchanan
- Media item
- Mar 27, 2016
- chair copy corner photos process thomas white
- Comments: 0
- Album: Thomas White corner chair
first_assembly

first assembly
- Charlie Buchanan
- Media item
- Mar 22, 2016
- chair copy corner photos process thomas white
- Comments: 0
- Album: Thomas White corner chair
wrap
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
veneers
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
time_2
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
tape
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
support
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
stop
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
start3
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
production
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
laminated
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
glued
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
form
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
compress
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
blank_ready
- Phil S
- Media item
- Aug 16, 2014
- blank bracelet process
- Comments: 0
- Category: Member Galleries
Cherry Maloof Bar Stools Ammonia Fuming Process

I just completed construction of two Maloof Bar Stools using the plans from Scott Morrison. These are made with Cherry and Ebony plugs. The first photo shows the two stools sanded to 400 grit and ready for finish. The background is a tent constructed from PVC, plastic and duct tape to seal the...
- cyclopentadiene
- Thread
- Jan 17, 2012
- ammonia bar cherry fuming maloof process stools
- Replies: 8
- Forum: "How To" Forum
Shop expansion - The process begins

Tuesday afternoon and Wednesday, Tony Morrison, my son's new father-in-law, started the foundation for my shop expansion. I am adding a 36' by 48' building with 12' ceilings to my existing 36' by 48' shop. We had to haul in 7 tri-axle loads of dirt to raise the subgrade. Here it is loking back...
- Sanders Fine Woodworking
- Thread
- Nov 4, 2011
- begins expansion process shop
- Replies: 31
- Forum: Workshop Discussion
H
Heartwood Pine table - process, trestle base (continued) and saddle joint

So here's the last in a series of posts on how I made this trestle table. 3 previous threads were: 1. General: http://www.ncwoodworker.net/forums/showthread.php?t=37044 2. Table top process: http://www.ncwoodworker.net/forums/showthread.php?t=37048 3. Trestle Base process...
- Henry W
- Thread
- Feb 4, 2011
- base continued heartwood joint pine process saddle table trestle
- Replies: 4
- Forum: General Woodworking
H
Heartwood pine table - process - table top

This is the first of a few threads that I am planning that detail my fabrication of this table initially described in this thread (started earlier today) http://www.ncwoodworker.net/forums/showthread.php?p=353122#poststop Here is the finished product in it's final destination: I purchased S4S...
- Henry W
- Thread
- Feb 2, 2011
- heartwood pine process table top
- Replies: 6
- Forum: General Woodworking